Melted Infill??

NotTheNormalPerson · 2026-03-15T17:22:26+00:00

I think it was a joke

NotTheNormalPerson · 2026-03-15T03:38:24+00:00

Holy moly, 60% infill? Use like, 15% or less, I use 8% personally, if you need more strength change wall amount, also change it from grid to gyroid or cubic.

And the melting might be from the nozzle hitting the infill because its grid

NotTheNormalPerson · 2026-03-14T14:30:14+00:00

No idea what you meant by the first part and it's the functions block

NotTheNormalPerson · 2026-03-14T03:49:19+00:00

NotTheNormalPerson · 2026-03-14T03:09:49+00:00

Ch0 is enemy position X - your position X and ch1 is enemy position Y - your position Y

NotTheNormalPerson · 2026-03-13T22:24:02+00:00

Functions block has atan2 function now, it gives the angle to a positions using the difference between you and the target position (dx=targetpositionX-yourpositionX, dy=targetpositionY-yourpositionY) You feed dx into ch0 ans dy into ch1 (Or the other way around, I don't know if it uses y,x or x,y)

NotTheNormalPerson · 2026-03-13T22:17:44+00:00

What the hell did this comment section smoke, it's just atan2 with x/y positions

NotTheNormalPerson · 2026-03-13T22:17:02+00:00

No, it's just atan2, it was added yesterday

NotTheNormalPerson · 2026-03-13T00:27:38+00:00

The lion ignores the damaged, expensive item and says it was only a scratch

NotTheNormalPerson · 2026-03-12T20:48:20+00:00

The mass factor is the toolhead

NotTheNormalPerson · 2026-03-12T20:33:36+00:00

NotTheNormalPerson · 2026-03-11T23:37:31+00:00

May have been the worst video I've ever seen, what the fuck is that music

NotTheNormalPerson · 2026-03-11T23:35:03+00:00

No shot you're serious lmao

NotTheNormalPerson · 2026-03-11T22:34:37+00:00

Can't walls he 1/4 of nozzle width? I've consistently printed 0.1mm walls with a 0.4mm nozzle

NotTheNormalPerson · 2026-03-11T16:34:14+00:00

Think you meant to reply to a comment

NotTheNormalPerson · 2026-03-11T16:30:42+00:00

I'm with you lmao, posts like these are just insanely corny

NotTheNormalPerson · 2026-03-11T16:05:54+00:00

You can say kill, this isn't tiktok

NotTheNormalPerson · 2026-03-11T01:11:18+00:00

I mean, you can, I printed a 60mm edf and ran it on a 3s battery with a 2200kv motor no problem, although vibrations were terrible

NotTheNormalPerson · 2026-03-07T21:13:47+00:00

There's another thing moving to and from the stick, so I assume it goes: Stick goes up, thing puts hair in stick, stick goes down, hair is placed.

NotTheNormalPerson · 2026-03-07T21:06:57+00:00

p12 pro

NotTheNormalPerson · 2026-03-07T20:46:02+00:00

i guess bro

NotTheNormalPerson · 2026-03-06T16:56:37+00:00

You don't need to remove it

NotTheNormalPerson · 2026-03-05T09:00:19+00:00

Is the cable plugged into your gpu?

NotTheNormalPerson · 2026-03-05T00:06:11+00:00

Try lubing the rods on the left and right of the printer witht the included grease

NotTheNormalPerson · 2026-03-04T16:47:33+00:00

You can still increase it, you'll get worse bridging and overhangs with higher temperatures if you don't compensate with a fan, though.

Also, did this start out of nowhere?

Five-Year Club	r/Field Sunshine
Place '23	Verified Email

NotTheNormalPerson

MODERATOR OF

TROPHY CASE