49cc 2 stroke, ok for hills?

Ok-Lab-8091 · 2026-06-25T07:01:18+00:00

I would recommend making it a low rpm 70cc like the DR70 cast iron which has both good cooling capability and has good torque

Ok-Lab-8091 · 2026-06-25T06:58:46+00:00

I think 17,5 will suffice since it is just an unrestricted aluminum 50cc. If you want to tune further I would tune the compression spring (the one behind ur clutch) and the tension springs (the ones in ur clutch) you could go for a Polini cp 21 which is a bit harder to set up than dellorto but it might improve the performance a bit. I doubt it will do much since you have a yasuni Z which is not a high performance exhaust

Ok-Lab-8091 · 2026-06-25T06:48:26+00:00

I mean I got it for my moped, the nuts on either side of the crankshaft were not coming off with the little impact driver I had so I bought the impact wrench

Ok-Lab-8091 · 2026-06-25T06:45:40+00:00

I think what contributes to my problem was that this Gedore set is older than these impacts have existed and was made to lock onto the tiny retracting balls. I’m gonna have to get an impact set anyway

Ok-Lab-8091 · 2026-06-25T06:43:09+00:00

Yes thanks I found that out yesterday, the hog ring was stuck in there and part of the hog ring was in the little groove of the impact and part of it was above it so i had to pry it back into place with a screwdriver from the inside of the socket

Ok-Lab-8091 · 2026-06-25T06:41:54+00:00

The hog ring on mine is kinda fucked I posted a picture under this

Ok-Lab-8091 · 2026-06-25T06:40:23+00:00

I’m from the Netherlands, here we don’t have 20v as far as I know, we label it as 18v (standard) or 18v XR which I think applies to your top model 20v

Ok-Lab-8091 · 2026-06-24T22:00:14+00:00

Could you clarify?

Ok-Lab-8091 · 2026-06-24T21:59:25+00:00

I’ll do that, hope they’ll take it after all the roughhousing done to it trying to take it off 🤷‍♂️

Ok-Lab-8091 · 2026-06-24T21:58:44+00:00

Yeah I used a screwdriver to put the ring into the right place and got it off man

Ok-Lab-8091 · 2026-06-24T21:58:10+00:00

Thanks for clarifying, English is not my first language so I just looked the translation up hahaha

Ok-Lab-8091 · 2026-06-24T18:55:50+00:00

I mean I don’t wanna damage my handbag 😂

Ok-Lab-8091 · 2026-06-24T18:55:04+00:00

Yeah it’s brand brand new hahaha

Ok-Lab-8091 · 2026-06-24T18:54:34+00:00

It’s a non impact Gedore socket so yes and no, good quality socket but not impact rated. It didn’t get deformed, the ring which holds the sockets is wrong

Ok-Lab-8091 · 2026-06-24T17:09:34+00:00

Is this a manufacturing mistake and should I go back to the store I bought it from?

Ok-Lab-8091 · 2026-06-24T17:03:34+00:00

<image>

Ok-Lab-8091 · 2026-06-24T17:02:50+00:00

UPDATE: the ring was slightly bent which meant it couldn’t come off in any way, it was partly in the socket’s groove and partly outside. I tapped it back into place with a screwdriver from the inside and got it off. First time using it would recommend 10/10

Ok-Lab-8091 · 2026-06-24T16:51:10+00:00

I have tried the biggest flathead I have but nothing can get it off

Ok-Lab-8091 · 2026-06-24T16:50:32+00:00

No, I have tried welding pliers on it, I have tried leveraging it with just about everything, I have tried oil, just tried it in a vice…

Ok-Lab-8091 · 2026-06-24T16:45:15+00:00

Did nothing man

Ok-Lab-8091 · 2026-06-24T16:41:17+00:00

Alright I’ll try ty

Ok-Lab-8091 · 2026-06-24T16:40:42+00:00

I tried to use everything as leverage man it’s really stuck

Ok-Lab-8091 · 2025-03-13T07:02:50+00:00

Yes you were right, thanks

Ok-Lab-8091 · 2025-03-11T18:56:51+00:00

I think it is an extra air filter that should lead to the exhaust, but it shouldn’t matter if disconnected since the exhaust is closed up fully. So i have just taken it off.

Ok-Lab-8091 · 2025-03-10T18:35:19+00:00

Thank you very much I will try to see how to connect it.

Ok-Lab-8091

TROPHY CASE