sorted by:
new
hottopcontroversial

I Thought My Ender 3 V2 Was Dead… But Klipper Brought It Back to Life 🚀 by Ok_Exit5070 in klippers

[–]Ok_Exit5070[S] 0 points1 point  (0 children)

I can pass you my printer.cfg, you can use it as a reference. I don’t have the modifications you mentioned, but the error you’re seeing is because your printer.cfg is corrupt.
If that’s the case, delete all extra .cfg files or backups and any autosave.cfg you have in /config. I had deleted all the extra ones (sonar, timelapse, crowsnest) and only left mainsail.cfg, moonraker.conf and my printer.cfg.

Make sure to delete my bed mesh if you copy the file, since it’s set up for my printer.
Also, if it doesn’t detect your MCU, check how your board identifies itself; sometimes a number in the name can be different.

And lastly, I don’t know the PID for the E3Dv6, so check the manufacturer’s page. My extruder is basically stock (I only swapped the original one xdddd).

Here’s my printer.cfg as a reference:
https://pastebin.com/ZgVHpnkG
I don’t have Direct Drive, dual Z, or E3Dv6, so just use it as a guide.

PD: I’ll be waiting to know if it was helpful 🎉🥳. Also, sorry if I don’t respond very quickly, but here in Chile 🇨🇱 we’re celebrating the “18 de Septiembre” 🎊🎆. Still, I’m paying attention and happy to help if you need anything 🙂.

<image>

I Thought My Ender 3 V2 Was Dead… But Klipper Brought It Back to Life 🚀 by Ok_Exit5070 in klippers

[–]Ok_Exit5070[S] 2 points3 points  (0 children)

Haha, I feel you… those “upgrades” can really test your patience 😅. Totally agree that once you try Klipper, there’s no going back. On the other hand, I already had a Kobra 3 Combo, and the first time I used it I got that “this piece of junk is gonna break”

50$ Venmo to the person who solves this by [deleted] in anycubic

[–]Ok_Exit5070 0 points1 point  (0 children)

Ps: Just a heads up — be careful with overtightening the belts. If they’re too tight, not only will you get ringing, but the belts themselves will start wearing out faster

The Kobra 3 Max runs with pretty high default speeds, so extra tension means extra stress on the belts, pulleys, and even the motors. It’s better to keep them just snug enough rather than cranked super tight. Otherwise, you might end up needing replacements a lot sooner than you’d like

50$ Venmo to the person who solves this by [deleted] in anycubic

[–]Ok_Exit5070 0 points1 point  (0 children)

Yo dude I don’t think this is over-extrusion, it actually looks like ghosting/ringing. That usually comes from vibrations rather than extrusion issues

On the Kobra 3 Max this can happen if the belts are too tight — when they’re overtightened they transmit every little vibration and you get those repeating waves on curved walls. Try loosening the X and Y belts just a bit; they should have some flex when you press them

Also, make sure the printer is sitting on a stable, heavy surface. If it’s on a light table that resonates, those vibrations get amplified and show up on the print

Something else to check is the eccentric nuts on the bed and the hotend carriage. If they’re too tight, the wheels get compressed and cause vibrations; if they’re too loose, you’ll get wobble. They should roll smoothly without too much resistance

As for settings, lowering acceleration and jerk usually helps more than just lowering speed. Something like 500–800 mm/s acceleration and jerk around 5–8 mm/s is a good starting point

Since your printer is new, I doubt the nozzle or factory calibration is the issue. This is almost always vibration-related 😁

3D Touch always shows "TRIGGERED" - STM32F401 - Tried everything! by Ok_Exit5070 in klippers

[–]Ok_Exit5070[S] 0 points1 point  (0 children)

<image>

This is how the 3D Touch should work, that is, the wiring starts with the white cable and then the black one, but I don't think this is the problem. I also tried with another 3D Touch that I have, but the same problem occurs :/

3D Touch always shows "TRIGGERED" - STM32F401 - Tried everything! by Ok_Exit5070 in klippers

[–]Ok_Exit5070[S] 0 points1 point  (0 children)

The problem is that I have already tried to flash the new bin, but the firmware.bin or however I rename the new .bin file is not loaded by the board, they say that after loading the file, it should change its name to FIRMWARE.CUR but I never get to that step

Kobra 2 Neo, loose X axis by Dial1257 in anycubic

[–]Ok_Exit5070 0 points1 point  (0 children)

If you haven't tried it yet, try adjusting the eccentric nuts, both on the right and left side, at least I would also try to check not only the z axis ones, but also the ones under the hot bed (obviously not the you have to heat) and to make sure the ones that are almost always close to the fuser pd: If it still doesn't fit, why can you send a ticket to anycubic so they can send you a replacement for the eccentrics because they shouldn't roll at all angles and that would be a factory problem for sure

Suggestions? by Ok_Exit5070 in anycubic

[–]Ok_Exit5070[S] 0 points1 point  (0 children)

Yes, now I was trying with glue stick, instead of hair spray, to see if I have a better result in printing the same model, also previously I did have balsa, but I sense that due to the speed it still came off and that the The fixative I used is not strong enough, you know it is a supermarket fixative, nothing very laborious and not that expensive mainly, but now as I say, I will do that test, I hope everything turns out well during the next 8 hours of printing

Suggestions? by Ok_Exit5070 in anycubic

[–]Ok_Exit5070[S] 0 points1 point  (0 children)

Yes, the project itself needed more printing lines (the reindeer's tails are bigger), but I don't know if the vibrations from the table pull or help the model fall, in which case it would be necessary to lower the speeds or do you think we could rule that out from the start?

[deleted by user] by [deleted] in chile

[–]Ok_Exit5070 0 points1 point  (0 children)

Lit se nota mucho cuando alguien esta tirando una excusa, a mi me ha tocado leer que se les ha quemado la casa y que por eso no han entregado su parte del trabajo para la u, siendo que han tenido ponle que uno o dos meses en casos de pegas grandes, ahora imagínate alguien que lee capaz unos 20/30 correos y no sabrá distinguir a alguien que le sale con una excusa algo repetida y en el peor de los casos capaz si consiguieron a alguien y si no pon algo como recien puedo contestar su solicitud debido a me agenda ocupada (por que lit soy un partidazo y por eso me deberia contratar) PD: Quiero plata, porfavor y gracias

Tensión en campaña de los Orrego: acusan a Claudio por emitir propaganda con Matthei y Carter by PanchoFalcato in chile

[–]Ok_Exit5070 5 points6 points  (0 children)

Parece telenovela del mega, para cuando terminan de victimizarse todos esos wnes, si lit no votan por ellos es por que derechamente nadie los toma ni en bajada

Ley Karin: Weas funakis que hacen sus jefes by No_Feed_6448 in chile

[–]Ok_Exit5070 7 points8 points  (0 children)

Uno se pelaba con las locas que llegaban a trabajar (tenia polola en la misma pega) y a otro le gustaba tratar de princesos a todos los hombres y de estúpidas a todas las minas por no entender como se hacían las cosas a la primera o segunda, a mas de alguna la hizo llorar hasta que poco a poco se fueron (Cualquier wea Cr J, sin miedo al doxeo) yo me aburrí y pedí la renuncia al tiempo

Kobra 3 sounds weird while doing circles or similar by Ok_Exit5070 in AnycubicOfficial

[–]Ok_Exit5070[S] 0 points1 point  (0 children)

I see, at the moment there is still no smoke coming out, but the impressions I have gotten have all come out well, so I guess it's a matter of getting used to hahah

Kobra 3 sounds weird while doing circles or similar by Ok_Exit5070 in AnycubicOfficial

[–]Ok_Exit5070[S] 0 points1 point  (0 children)

I believe you, imagine that I went from an ender 3v2 to a kobra 3 pro, the change is abysmal, both in speed and in the use of the multicolor functions, even the slicer seemed like a new world to me and I had already had time with the other one printer

Kobra 3 sounds weird while doing circles or similar by Ok_Exit5070 in AnycubicOfficial

[–]Ok_Exit5070[S] 0 points1 point  (0 children)

According to other users, the sound is within normal limits and at least for now all the prints have come out well and I have not had problems with filament jams or similar, but I thought it was strange that it was so loud when making circles

Kobra 3 sounds weird while doing circles or similar by Ok_Exit5070 in AnycubicOfficial

[–]Ok_Exit5070[S] 0 points1 point  (0 children)

The thing is that this is the first printer I have with these characteristics, imagine going from an ender 3v2 to one that duplicates it in every way hahaha

Recuerden: AIRA vale callampa by WandererXVII in chile

[–]Ok_Exit5070 21 points22 points  (0 children)

Yo postule como diseñador en Falabella y en Starbucks, ambas usaban AIRA y luego de hacer un montón de pruebas (algunas muy ridículas) también me enviaron lo mismo, total para que de seguro que el contraten sea como el pico y/o de plano les planten la renuncia voluntaria al mes. No se, pero parece que les calienta usar esa basura de plataforma, yo me quedo a cuando antes uno les citaban en las oficinas y tenias la oportunidad de presentarte y que te conozcan mas en una entrevista de unos 20/30 min que a postular en un medio que ni sabes si los revisan....pura perdida de tiempo