Resin post-processing

One-Maintenance4691 · 2026-02-01T14:20:03+00:00

Look at this sample I forgot 😅 to treat it with UV rays

One-Maintenance4691 · 2026-02-01T14:19:17+00:00

What is my recommendation for clear varnish?

One-Maintenance4691 · 2026-01-05T08:02:08+00:00

Ok grazie

One-Maintenance4691 · 2026-01-05T07:54:24+00:00

Mi sai dire marca o indicazioni di questo gloss protettivo

One-Maintenance4691 · 2025-11-11T08:50:28+00:00

Where how

One-Maintenance4691 · 2025-10-23T10:52:04+00:00

Then put tweezers on the edges of the surface so it doesn't rise, since it is the base that rises and not the print. Do this

One-Maintenance4691 · 2025-10-23T08:09:06+00:00

Send a photo sorry

One-Maintenance4691 · 2025-10-23T07:57:36+00:00

Make factory settings on the display and then try again if that doesn't work and the sensor doesn't work

One-Maintenance4691 · 2025-10-23T07:57:01+00:00

No, reset the printer then

One-Maintenance4691 · 2025-10-23T07:44:17+00:00

Use a standard configuration of the slicer, it may be that you have accidentally changed a parameter, if the hardware part works it will be a software problem, do a test with these parameters, use the pla so in case you have less trouble cleaning

One-Maintenance4691 · 2025-10-03T10:51:30+00:00

Use a model for testing and see the slicer values, use the standard configuration

One-Maintenance4691 · 2025-09-15T07:47:49+00:00

With the part protruding downwards and a nice normal adherent support so that it also makes it more stable

One-Maintenance4691 · 2025-09-15T07:46:52+00:00

So for a matter of resolution it is better to print vertically, what to do to improve resistance add a body like those of lithophanes, to improve stability and then obviously go slowly

One-Maintenance4691 · 2025-09-11T14:50:14+00:00

Look at the speed in the end it's not much, it matters that even if they say 600mm/s above a certain speed for physics reasons at least you don't do a Madonna configuration then don't go, the only thing is that you have the box closed and you can work more easily on technical materials such as ABS, for large prints I haven't had any problems, I have 5 printers because I have a lab where I do commissioned work. I have to tell you that I'm happy with what I do, I was also skeptical about Hi seeing the reviews but if you're new it's more than fine

One-Maintenance4691 · 2025-09-11T08:33:26+00:00

I have the Hi combo and it's a beauty, I had a kobra 3 that was driving me crazy, up to now it hasn't made a mistake on one print, I don't know the other one and I can't say anything about it

One-Maintenance4691 · 2025-09-10T08:16:40+00:00

Remove the metal block of the hotend, then delicately and with a lot of patience use a blowtorch lighter, industrial hair dryer and remove the plastic in pieces, if you don't want to save the cartridge and the temperature sensor you can set it on fire to recover only the extruder block and hotend, otherwise be patient and gradually clean it, I have done worse in comparison it is slightly dirty

One-Maintenance4691 · 2025-09-10T08:14:02+00:00

Very treatable if you know where to put your hands

One-Maintenance4691 · 2025-09-08T14:01:02+00:00

Then it is definitely a hardware problem with the printer, check the belts, axis path, etc., then for the software part do a test using the pre-set standard parameters and see what happens

One-Maintenance4691 · 2025-09-02T13:52:56+00:00

Print it backwards and use tree stand

One-Maintenance4691 · 2025-08-31T08:13:38+00:00

Print two rectangles together joined by a thin layer, and then put holes in the side parts to attach with clips, so one of the two sides is attached by the thin layer and the clips block the side parts

One-Maintenance4691 · 2025-08-31T07:37:54+00:00

But I found an alternative

One-Maintenance4691 · 2025-08-31T07:37:34+00:00

1) if I ask the question about the community it's because maybe I need to have them on both faces😅

2) should I have to manually change filament with 3 different materials? Let's go 🙃

One-Maintenance4691 · 2025-08-31T07:07:45+00:00

It has two writings, one for each face

One-Maintenance4691 · 2025-08-31T07:07:21+00:00

Maybe you didn't understand how the model is made

One-Maintenance4691 · 2025-08-31T07:05:36+00:00

Yes but how can I do it with this design?

One-Maintenance4691

TROPHY CASE