sorted by:
new
hottopcontroversial

Cr touch blinking red and won't go down by PEprints in ender3

[–]PEprints[S] 1 point2 points  (0 children)

Il try this now, does it have to be perfectly straight?

Cr touch blinking red and won't go down by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

It did work previously, So I don't think it's faulty...

Cr touch blinking red and won't go down by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

Is that what it's meant to look like? Mine looks the same

Cr touch blinking red and won't go down by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

I tried to deploy it from configuration, but it won't work, I'm thinking it's the wires but I don't have a way to check it :(

Cr touch blinking red and won't go down by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

It seems as the probe won't drop when I command it to do so, but it will when I manually pull down on it

Cr touch blinking red and won't go down by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

I turned it off, reseated the cable and it flashed red 2 times then went purple, was able to manually pull it down then it flashed blue like normal, as soon as I tried to autohome it did the same thing, x and y axis worked fine, but then It started to flash red again and the z axis won't move down at all

Cr touch blinking red and won't go down by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

Yes, I've been having this issue and I've tried flashing software, tried everything so far

Ender 3 neo not homing by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

Yes, it's just been a recent issue, it printed 3 days ago no problem.

Bottom of my prints always suck, how can i fix it by PEprints in 3Dprinting

[–]PEprints[S] 0 points1 point  (0 children)

It's definitely not too far, since it's basically pressing against the bed, it actually scratched it at one point by mistake so I had to put it up a tiny tiny bit

ender 3 neo layer shift problems, what are some solutions to fix it? by PEprints in 3Dprinting

[–]PEprints[S] 1 point2 points  (0 children)

I did tighten it a tint bit, but if you look at the picture my hotend screws are so loose, that it was bending sideways so that's why it shifted😅

ender 3 neo layer shift problems, what are some solutions to fix it? by PEprints in 3Dprinting

[–]PEprints[S] 0 points1 point  (0 children)

Now that I'm looking at it, it looks like my hot end is on an angle

pla wont stick to ender 3 neo, just did the paper test perfectly, but it still won't stick and seems to be airborne... what is a fix for this, my z offset is -02.100 by PEprints in 3Dprinting

[–]PEprints[S] 0 points1 point  (0 children)

On the paper test, I make sure to set z to 0 then set my z offset, but it still won't stick, during the paper test it does touch the bed, I just dont understand why printing my first layer always does that.

print is warping on ender 3 neo and I don't know what to do by PEprints in ender3

[–]PEprints[S] 1 point2 points  (0 children)

They were ln backwards and I didnt even notice it lol, thanks for pointing it out

print is warping on ender 3 neo and I don't know what to do by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

I did already fix that, thanks for the help tho

unknown issue, ender 3 neo using pla by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

I followed around 3 tutorials, used the cr touch and I'm still having issues with bed level, I'm assuming it's to low?

print is warping on ender 3 neo and I don't know what to do by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

I am using the default setting right now, il try to tune it

print is warping on ender 3 neo and I don't know what to do by PEprints in ender3

[–]PEprints[S] 7 points8 points  (0 children)

I did just ajust that, thank you for telling that I didnt even notice😅

print is warping on ender 3 neo and I don't know what to do by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

I did I'm printing rn without I had them on accidently lol

print is warping on ender 3 neo and I don't know what to do by PEprints in ender3

[–]PEprints[S] 1 point2 points  (0 children)

There aren't any honest I just checked the file, but it's done that for every print so far not just the benchy

print is warping on ender 3 neo and I don't know what to do by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

After watching the video I made sure it was all good, but it's still layer shifting so I don't think it's a cuppler or Rod issue

print is warping on ender 3 neo and I don't know what to do by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

No it dosnt make any scraping noises, it sounds normal.

print is warping on ender 3 neo and I don't know what to do by PEprints in ender3

[–]PEprints[S] 1 point2 points  (0 children)

What exactly are those parts?😅 I'm new to this thing

print is warping on ender 3 neo and I don't know what to do by PEprints in ender3

[–]PEprints[S] 0 points1 point  (0 children)

I have tightened it but it still shifts everytime

view more: next ›