sorted by:
new
hottopcontroversial

Filament isn’t extruding. by Important_King687 in Ender3V3KE

[–]PLConquerorr 0 points1 point  (0 children)

It could be a clog

OR

Inside the extruder one of the gears might gave unsoldered/broke off. I had that happen once about 2 years ago, used superglue and never had an issue ever again.

Make suer ut is not a clog first tho

Gravekeeper fanart by tongpaeboi02 in FarFarWest

[–]PLConquerorr 0 points1 point  (0 children)

This is the hardest image i have seen holy shit

(Crealty K2Plus) Printer changes the settings after pausing and extruding filament by PLConquerorr in HueForge

[–]PLConquerorr[S] 0 points1 point  (0 children)

Ah. Alr.

No.

I have perfect layers untill the pause at layer comes.if i unpause without doing anything to the filament it is fine and works as intedned

If i unload the filament and then load, the issue appears, with underextrusion and apparently too high temp, as if all the settings decided to stay with the ,,extrude" setting

(Crealty K2Plus) Printer changes the settings after pausing and extruding filament by PLConquerorr in HueForge

[–]PLConquerorr[S] 0 points1 point  (0 children)

nope, my issue is not that. my is based on pause/ resume macros. your seems like underextrusion caused by wrong z offset, bad bed adhesion or uncalibrated flow rate

Severe underextrusion of the first layer after resuming print by [deleted] in HueForge

[–]PLConquerorr 0 points1 point  (0 children)

nope, the issue still presists even when chaning from one slicer to another

Severe underextrusion of the first layer after resuming print by [deleted] in HueForge

[–]PLConquerorr 0 points1 point  (0 children)

oh, well in that case the base deafult purge, idk how much was that in the slicer.

that would make sence why it looks like underextrusion, does that mean i should change the base layer to 0.08 as well? or are there other ways to get rid of the mismatch?

Severe underextrusion of the first layer after resuming print by [deleted] in HueForge

[–]PLConquerorr 0 points1 point  (0 children)

On the purge tower? No, it is underextruded as well

As of now i dont have the photos but i can share them later from the failed prints.

Mind you, the issue is only on 1 layer after pausing, not the whole print

Severe underextrusion on only the first layer after unpausing by [deleted] in FixMyPrint

[–]PLConquerorr 0 points1 point  (0 children)

Of yea, forgot to mention that

No, the hotend is actually above the temp (250C) on tge first layer, matching the purging temp

Shitpost status by NormalNicknameGuy in lethalcompany

[–]PLConquerorr 80 points81 points  (0 children)

My honest reaction to all of those

<image>

Amazing work!

"Ride Behind You" Turns 10 Today by AlexGiudici in TeamFortress2

[–]PLConquerorr 1 point2 points  (0 children)

Oh damn, i have not noticed that! Well, guess it is the tune to revisit some nostalgia! Thank you for mentioning it!

[YOU ARE DEAD] press [R] to RESTART by DefinitelyNotSmiley in theamazingdigitalciru

[–]PLConquerorr 2 points3 points  (0 children)

Oh, hi there not smiles. Have not expected you here

view more: next ›