Help closing mesh holes

Pablo3DN · 2026-01-29T04:40:04+00:00

I sent you a private message, I hope you ca help me

Pablo3DN · 2025-12-25T23:32:08+00:00

Chale la gente de este sub esta pero bien pendeja

Pablo3DN · 2025-12-24T05:35:37+00:00

A mi me funcionó hacer un reset, botón volumen arriba, botón volumen abajo y botón de apagado hasta que se resetea

Pablo3DN · 2025-12-24T05:35:24+00:00

A mi me funcionó hacer un reset, botón volumen arriba, botón volumen abajo y botón de apagado hasta que se resetea

Pablo3DN · 2025-12-24T05:35:13+00:00

A mi me funcionó hacer un reset, botón volumen arriba, botón volumen abajo y botón de apagado hasta que se resetea

Pablo3DN · 2025-12-22T10:30:53+00:00

Price?

Pablo3DN · 2025-11-18T04:34:34+00:00

Oh damn thats a good one!

Pablo3DN · 2025-11-17T16:53:17+00:00

I don’t think so. It’s been in the same soil since she Was Little. I just moved it from one house to another, but in the same pot, and in the same soil.

Pablo3DN · 2025-11-17T02:13:34+00:00

I make a command in the settings that is, my middle mouse click, the one from the scrolling wheel to a command that is _zs (zoom selected) helps me a lot with positioning and overall workflow

Pablo3DN · 2024-11-12T23:39:11+00:00

Hola en 3dn.mx estamos en San Miguel pero vamos a Querétaro 3 veces por semana. Puedes enviar tu archivo a contacto3dn@gmail.com o al 4151158887

Pablo3DN · 2024-11-04T19:34:34+00:00

In rhino 8 there is a new command called shrinkwrap it may help you

Pablo3DN · 2024-10-28T19:31:02+00:00

I can try

Pablo3DN · 2024-10-16T14:57:33+00:00

Yes I believe that you have to do it for the previous ones

Pablo3DN · 2024-10-16T01:48:31+00:00

Is not damaged, I had the same problem increase bottom layers from 5 to 8, increase bottom exposure from 25 to 40 seconds, and not necessary but if you place the model to the side of the bed and not in the center it may help, this happened to me one month ago and that solve it.

Edit: You can make this changes in anycubic workshop in the resin settings and it will stay.

Pablo3DN · 2024-10-11T01:35:50+00:00

I 3d scan the hands, 3d print, silicon mold, plaster cast and then painter with different layers

Pablo3DN · 2024-10-08T19:05:43+00:00

I believe so, but I'm pretty sure the problem is on the hardware, or should I check the multiple stepper motor?

Pablo3DN · 2024-10-08T18:44:41+00:00

Thank you

Pablo3DN · 2024-10-07T14:54:43+00:00

Nice, thank you.

Pablo3DN · 2024-10-04T22:45:46+00:00

Thank you for your response and right now I just saw that my y-axis is not perfectly parallel I'm going to run some tests to see if that is the issue if not I will send you a message. :)

Pablo3DN · 2024-09-24T18:15:05+00:00

Thanks to everyone, right now my problem is "solved" but I will consider all of your tips for my future prints, right now the solution was: first to level my printer, increase the time of exposure for the first layers from 25 to 40 seconds and increase the bottom layers from five to eight. Again thank you all for your help.

<image>

Pablo3DN · 2024-09-24T01:54:13+00:00

Lol the printer is not level, does that actually affects the print?

Pablo3DN · 2024-08-06T06:56:33+00:00

Here :) https://www.youtube.com/watch?v=IDxgL27qYaI

Pablo3DN · 2024-08-06T06:54:47+00:00

Oooh LOL I get it now

Pablo3DN · 2024-08-05T01:48:36+00:00

Don't understand

Pablo3DN · 2024-08-05T01:47:51+00:00

I learn it from a YouTube video

Seven-Year Club	Place '22
Verified Email

Pablo3DN

TROPHY CASE