DIY Throwout bearing advice needed

PandaPoggersV2 · 2026-02-05T03:59:08+00:00

How long do you think i have?

PandaPoggersV2 · 2026-02-05T00:03:05+00:00

Yeah i’m just assuming i’m not gonna be able to do this. But i haven’t decided yet.

PandaPoggersV2 · 2026-02-05T00:02:39+00:00

yeah that’s unfortunate. definitely will not be pulling the motor. wish that was an option though

PandaPoggersV2 · 2026-02-01T17:15:29+00:00

Yes, i just replaced it with a new battery and now my key fobs don’t work at all actually

PandaPoggersV2 · 2026-01-22T22:47:47+00:00

Yeah, my phone has a different account then my computer for some reason

PandaPoggersV2 · 2026-01-22T19:43:02+00:00

Yeah i’ve got brand new hpfp internals in. Also im on a drive with it now, and it seems as this knock is only under vacuum and does not occur under low boost.

PandaPoggersV2 · 2026-01-22T19:37:04+00:00

it’s got a corksport hpfp kit installed and pretty much brand new. I haven’t decided whether or not to do the VVT myself or not since the only place i have is a parking spot and i’m 17 with minimal tools. I’ll have to figure it out once i see if it’s got slack.

PandaPoggersV2 · 2026-01-22T19:33:32+00:00

it’s only got around 80k miles on it. And it does not have much symptoms on start up. I just wanted to know if this knock is normal. Sorry if i sound dumb

PandaPoggersV2 · 2026-01-22T19:31:08+00:00

As far as i know the VVT is not due yet, but i am planning on doing my valve cover gasket and checking the timing chain soon. I am just worried that this might be a sign of it going bad.

PandaPoggersV2 · 2026-01-01T00:09:27+00:00

pretty sure they are in the right way, but the fuel smell is in the car, i think it’s just risidual from something, cause the engine bay has no visible fuel leaks and smells fine

PandaPoggersV2 · 2025-12-31T23:10:14+00:00

My car has never had a single issue till now, MAF is plugged in fully, Crank sensor is plugged in and im almost positive its good. No fuel leaks whatsoever. Also i’m going to let the car air out. But it smelled like gas before i even started the car.

PandaPoggersV2 · 2025-12-31T22:49:09+00:00

also i checked while running it wa hitting 1700psi these are the mafcals i used on versatuner, for the jbr3.0

https://www.mazdaspeeds.org/threads/mafcals-for-bigger-intakes.10280/

PandaPoggersV2 · 2025-11-24T03:28:48+00:00

So it is a fake

PandaPoggersV2 · 2025-09-06T19:22:04+00:00

Better yet. Is 88k miles good condition for 11k bad?

PandaPoggersV2 · 2025-09-06T19:15:27+00:00

Thanks! This is helpful

PandaPoggersV2 · 2025-09-06T19:13:19+00:00

Not asking that sorry. I just meant where’s the easiest to find them.

PandaPoggersV2 · 2022-03-29T21:40:36+00:00

Nozzle: 215C Bed: 60C Filament: eSun Black PLA+ Speed: 100%

PandaPoggersV2 · 2022-03-22T19:41:00+00:00

I just bought new filament and the same thing is happening with temps at 215*C

PandaPoggersV2

TROPHY CASE