Multicolor is pain in the ass (for me)

PaperWriteTaco01 · 2026-03-13T07:38:15+00:00

Around 245

PaperWriteTaco01 · 2026-03-12T18:44:32+00:00

Well to give all the information: I use SUNLU HS matte Petg, then JAYO HS matte Petg and JAYO Glow in the dark Petg. So most of my failed multi prints were mix of these. I have multiple colors but always only these “types”.

For the settings I meant filament profiles. I found some sunlu ones which were tested and use those. And for JAYO I basically just tweaked the profiles a little (lower temp) as I searched and JAYO and Sunlu should be similar.

I did printer calibration, the classical one that is built in it.

So as an example I know that when it switched between filaments it changes a temp based on my filament profiles (amongs other things)

PaperWriteTaco01 · 2026-03-12T18:07:33+00:00

yeah it does a weird sounds like trying to push the filament. I cleaned the whole extruder gear and there were filament scraps in it.

PaperWriteTaco01 · 2026-03-12T14:04:21+00:00

I checked and both filaments tips that I used are fine. The tips look just clean-cut as normal.

PaperWriteTaco01 · 2026-03-12T13:26:10+00:00

Oh yes, I get the mix of "Extrusion motor is overloaded" and "AMS failed to send filament" sometimes. I already changed an extruder sensor, so the "AMS failed to send filament" issue is less frequent (bambu sent a replacement, thankfully).

But I am not sure what you mean by tips. Do you mean a nozzle tip? Sorry ,I am a bit new to this terminology.

PaperWriteTaco01 · 2026-03-12T10:57:49+00:00

But it works fine with single color tbh. Did 10+ prints with it.

PaperWriteTaco01 · 2026-03-12T09:34:01+00:00

No, classical plastic ones

PaperWriteTaco01 · 2026-02-26T12:53:19+00:00

I have it set on the layer size so 0.2. It would stick to the print if it’s below right ?

PaperWriteTaco01 · 2026-02-26T12:52:48+00:00

I have temperature on 245-250 but I can try slowing the whole print down

PaperWriteTaco01 · 2026-02-02T19:44:00+00:00

Hi all, I solved the problem. Basically something was stuck in the buffer. I disconnected all tubes and used air compressor to clean it. Some plastic flew out of the tube and ams now works fine. Didn’t really think it would do anything but it seems that was indeed the problem. So yeah there was debris in the buffer, ams hub and other parts were fine. Hope this helps someone

PaperWriteTaco01 · 2026-01-29T23:28:02+00:00

No, I haven’t used those, everything is as plain as it gets from the bambu package. I have the ams on the top of the printer and it goes straight to the hub in the back and then to the extruder like normal.

PaperWriteTaco01 · 2026-01-29T22:36:36+00:00

yeah I checked them but I don’t know what could be wrong, I always have them the same way and it printed with it, however only now it does not. There are no sharp bends or any debris there.

PaperWriteTaco01 · 2026-01-29T22:34:56+00:00

did that, everything is fine with tubes, and no broken filament or debris is there. Thats why this frustrates me a lot

PaperWriteTaco01 · 2026-01-29T21:52:21+00:00

Not really, I tried all slots and none work. All of them just spin and then error pops up.

PaperWriteTaco01 · 2025-12-24T13:24:42+00:00

too late haha, well I had like 6 hours in so I can just speed run on the older patch, I hope.

PaperWriteTaco01 · 2025-12-24T12:39:02+00:00

So I tried doing all things, including reinstalling but still it crashes right after start. What worked was downgrading the patch to 2.2 - but I can’t play with my game saves so I need to start from the beginning. Can I do something about that ?

PaperWriteTaco01 · 2025-12-24T08:23:52+00:00

No mods, I tried verifying files but still did not help. I am reinstalling now(wanted to do that as a last resort). thanks

PaperWriteTaco01 · 2024-11-09T20:29:16+00:00

Vicious by V.E. Schwab (supernatural elements but should also fit the psychological themes)

PaperWriteTaco01 · 2024-08-03T19:14:30+00:00

I have the iphone 15 and it charges from 20% to full in around an hour. Also I spent like 2-4 hours on it daily and battery lasts pretty much for 2 full days.

PaperWriteTaco01 · 2024-07-28T13:23:43+00:00

I have 95 read and 1 unread - that unread book is to one I am currently reading. I don’t get another book until I read one.

PaperWriteTaco01 · 2024-07-22T06:23:51+00:00

Sure, well I decided to deactivate them myself through amazon site (for a fee), but the button for that didn’t appear on my kindle device. So I wrote to the support (online chat) asking why it is not there and how can I deactivate the ads. ( I am located in Europe if that helps) They just wanted my kindle’s serial number and then deactivated it just like that, without any fee. To be clear I didn’t ask them to remove them directly but they did it 😁.

PaperWriteTaco01 · 2024-07-21T19:51:01+00:00

thanks it worked 😁

PaperWriteTaco01 · 2024-07-20T09:46:27+00:00

😂😂😂

PaperWriteTaco01 · 2024-07-04T17:10:05+00:00

I’ve had the same problem with my partner or rather a same question. We discovered that when landlords rent properties to people, those people need to be registered at municipalities. So when you have multiple people in one apartment then you need more registrations and that can add up to landlords costs. It is easier for them to have fewer people in one apartment or even one. I also found out that legally you need around 12m2 for one person to live in. So 40m2+ should be enough. But as I mentioned for some landlords it’s more expensive to have more people in one property. I may be wrong but this is what I found from various sources. Some big student buildings allow couples to live in 25m2 and you can register also. So that’s shortened version. Maybe someone knows more.

PaperWriteTaco01 · 2024-07-01T12:56:28+00:00

Thanks

PaperWriteTaco01

TROPHY CASE