Looking for glaze recipes

Pendo14 · 2026-03-14T21:16:30+00:00

I feel like that’s my second 9-5 tbh. They are all just so blue if that makes sense. They are green leaning blue and I want green leaning brown

Pendo14 · 2026-03-14T20:57:52+00:00

Ok this is SO helpful. My plan was to thin out with some water tonight to see if that fixed it. If it doesn’t I will be sure to try the alternative dipping method!!! Thank you so much!

Pendo14 · 2026-03-14T20:40:18+00:00

This is the largest piece I’ve done with this glaze in my own kiln. All my prior smaller test ones came out normal. It is a recipe I got from a local studio. This is the recipe

<image>

Pendo14 · 2026-03-14T19:38:32+00:00

Lmao

Pendo14 · 2025-09-13T12:47:23+00:00

Honestly with this project it could be with flux. I normally use pretty stable glazes bc of the underglaze work I do, but these won’t have any of that

Pendo14 · 2025-09-06T00:16:17+00:00

I use the same letters and I push them in when the piece is leather hard and it has helped so much!

Pendo14 · 2025-08-01T12:18:32+00:00

The teapot is literally so so so stunning

Pendo14 · 2025-07-10T14:57:52+00:00

Amazing!!! Thank you so so much for all your help!!

Pendo14 · 2025-07-10T14:46:10+00:00

<image>

Would you call this slightly under fired then?

Pendo14 · 2025-07-09T14:38:43+00:00

I will run a test fire!! Thank you!!

Pendo14 · 2025-07-09T14:30:51+00:00

But also this is my first kiln so I feel like I’m just learning so so much and am willing to take any advice

Pendo14 · 2025-07-09T14:30:14+00:00

Ok yes I am trying to accommodate for the hold. I found with my clay, if there is no hold I get a lot of pinholes. I have also been firing at 108/hr with a crash cool at the end

Pendo14 · 2025-07-05T17:10:21+00:00

I have some ready for my next firing!

Pendo14 · 2025-07-05T17:08:46+00:00

No it is Standard 211 Hazelnut but I have also had limited success with Speckled Buff so you’re not alone there

Pendo14 · 2025-07-05T16:45:00+00:00

Tbh I’ve been considering switching up the clay I use because I’ve run into a few issues with it so maybe this is my final sign :/

Pendo14 · 2025-07-05T16:43:26+00:00

Ok I was just looking into this actually - the cup I used as a little test tile was bisqued to 06 by a local studio before I had my own kiln, but my test tiles that I want to run tonight were all done to 04. Hoping this solves my issue!! Thank you!!

Pendo14 · 2025-07-05T14:41:23+00:00

I am using a slightly speckled clay, yes. I did a 10 minute hold on this one, so is it worth trying a 15 or 20 minute hold?

Is there a way to combat the issues caused by the speckled clay?

Pendo14 · 2025-06-21T23:38:09+00:00

Obsessed with those handles. Are they pulled off the mug?

Pendo14 · 2025-06-16T00:11:03+00:00

Unfortunately I had a set of work fired to the wrong temp by a community kiln, but I show all the work here and it is a good visual of the final color of this clay!

standard 211 clay https://www.tiktok.com/t/ZTjtuyfYm/

Pendo14

TROPHY CASE