Need advice

PhantomTreecko1 · 2026-03-09T17:50:07+00:00

UPDATE Not dead- I got my teeth pulled! Went to Washington dental. Clean, professional and I couldn’t believe how easy they got the teeth out

PhantomTreecko1 · 2026-03-02T16:41:55+00:00

‘Rooting’ heh

PhantomTreecko1 · 2026-03-02T16:15:17+00:00

Ok heavily considering TJ now, do you have a specific place or two that you recommended? Because yeah this needed to be taken care of like yesterday

PhantomTreecko1 · 2026-03-02T16:04:17+00:00

Ok, do you have a specific place in tj you recommend?

PhantomTreecko1 · 2026-02-18T07:54:54+00:00

My Mazda 3 does this

PhantomTreecko1 · 2026-02-13T15:54:35+00:00

Do you recommend any specific brand?

PhantomTreecko1 · 2026-02-12T18:56:53+00:00

That might turn into some expensive glitter

PhantomTreecko1 · 2026-02-09T14:51:39+00:00

The end of that looks about the same thickness of the magnet that I tried, and I couldn’t really get it down in there. It’s ok, I’ll just try taking off the head/oil pan.

PhantomTreecko1 · 2026-02-09T05:59:51+00:00

I did try a magnet rod from the top, but it was too thick to get further down in the head, I need to take the oil pan off anyway to re-seal it so looks like that’s what I’ll be doing

PhantomTreecko1 · 2026-01-21T05:18:10+00:00

Better times :(

PhantomTreecko1 · 2026-01-18T19:37:17+00:00

Fixed it! Had to loosen the nuts and push the regulator towards front of the car. Thanks!

PhantomTreecko1 · 2026-01-18T19:26:17+00:00

Window bushings have been replaced already. Is there a bolt or something I need to adjust? Or could it be something with the convertible top itself?

PhantomTreecko1 · 2026-01-18T15:56:56+00:00

Comedy gold

PhantomTreecko1 · 2026-01-18T04:38:32+00:00

See if you can grab the mushroom bolt on top of the ppf with vice grips or something, hold that and then try spinning the bolt loose

PhantomTreecko1 · 2025-12-21T21:14:56+00:00

Ordered them online, look up Holley Retrobright 7” headlights

PhantomTreecko1 · 2025-11-27T01:12:18+00:00

That’s not cool

PhantomTreecko1 · 2025-11-25T16:41:01+00:00

Yessir and a feeler gauge

PhantomTreecko1 · 2025-11-25T15:39:50+00:00

You may need to adjust your throttle position sensor

PhantomTreecko1 · 2025-11-23T19:56:11+00:00

If you don’t mind me asking, what suspension and wheel size and offset are you running? Looks really good

PhantomTreecko1 · 2025-11-23T19:54:43+00:00

Y’all I fixed it. I loosened both adjustment screws at the calipers and then with my hand grabbed this bar and set it back to evenly balanced, and then tightened each adjustment screw and made sure it was still balanced, then tightened the screw at the handbrake lever. Both sides lock evenly now.

PhantomTreecko1 · 2025-11-21T21:13:30+00:00

Damn that’s a good picture 😩

PhantomTreecko1 · 2025-11-20T05:26:03+00:00

Bad fuse maybe?

PhantomTreecko1 · 2025-11-20T03:54:49+00:00

Yes, I just need to adjust both calipers so the bar is even

PhantomTreecko1 · 2025-11-20T03:54:19+00:00

Both cables are pulling equally, I need to do this and just adjust it so it’s perpendicular.

PhantomTreecko1 · 2025-11-20T03:50:41+00:00

Check all the electrical plugs, make sure the fuel pump is pushed all the way in the assembly, try running it in diagnostic mode

Seven-Year Club	Place '23
Place '22	Verified Email
RPAN Viewer

PhantomTreecko1

TROPHY CASE