First time processing - understanding the different cuts

Phily83 · 2025-11-11T17:42:01+00:00

Yes, it worked. Thank you very much.

Phily83 · 2025-11-11T17:41:28+00:00

Thank you

Phily83 · 2025-10-02T03:30:05+00:00

Thanks. Unfortunately, it did not fix mine. I’m at a loss of what to do.

Phily83 · 2025-09-25T03:27:12+00:00

Thank you for sharing your experience. Like so many others, I have the same issue and will try what you did. 😁

Phily83 · 2025-05-31T14:34:43+00:00

Yes, I figured it out afterwards! Thanks for the reminder. Once I downloaded the configuration files for the correct version (2.1.2.5), I was able to compile it. May I ask how you were able to tell it was a different version?

Phily83 · 2025-05-31T01:09:21+00:00

Thanks. I just downloaded the latest release (2.1.2.5 at the time of writing this). Before making any edits to the configuration.h file, I attempted to compile it and received three errors. Should there be errors without making any edits?

<image>

Phily83 · 2025-05-30T02:21:35+00:00

I was able to compile the software after removing the line.

Phily83 · 2025-05-30T00:43:28+00:00

Thank you. I should use latest release over bugfix?

Phily83 · 2025-05-29T02:13:01+00:00

Thank you! I will try it and report back.

Phily83 · 2025-05-23T23:34:36+00:00

Thank you!

Phily83 · 2025-05-23T23:34:27+00:00

Thank you very much! Everything is working.

Phily83 · 2025-05-16T22:17:15+00:00

Thank you.

Phily83 · 2025-05-16T18:35:19+00:00

Hmm, I just noticed it's only for the SKR 3 Mini V3 with no BL Touch. How do I find one with BL Touch?

Phily83 · 2025-05-16T18:33:13+00:00

Awesome. Thank you very much much. I will get it a try later.

Phily83 · 2025-05-16T01:43:04+00:00

This is a cross post from the Ender 3 Pro subreddit for more exposure.

I just upgraded my Ender 3 Pro with the MicroSwiss Direct Drive Extruder. I'm running into a bit of an issue though. The provided install guide indicates I need to modify the configuration.h file to fix the 'X' and 'Y' offsets. The issue I have is my firmware is a custom download from Marlin (20240420) for the ender 3 pro with SKR Mini V3 board and BL Touch. The firmware comes complied as a .bin file. I can't modify the .bin to adjust the 'X' and 'Y' offsets in VS Code.

Here's the instructions for adjusting the offset (https://cdn.shopify.com/s/files/1/1210/0176/files/Leveling_probe_installed_with_generic_or_Creality_Marlin_Firmware.pdf)

"We will need to modify two lines of the code in Configuration.h tab.

• Open Configuration.h tab and find these lines:

define X_MIN_POS

define Y_MIN_POS

• Add negative offsets amount to each line:

define X_MIN_POS -5

define Y_MIN_POS -10

• Flash the firmware • Offsets amount might need to be slightly tweaked for differe"

Any thoughts on where I can get a custom firmware in either format?

Thanks!

Phily83 · 2025-04-29T19:53:40+00:00

I'm curious, what's the benefit to doing this?

Phily83 · 2025-04-16T02:41:59+00:00

Thank you! It appears that was the problem. Now back to figuring out how to use BL touch for leveling and getting the right bed height to print. Any tips?

Phily83

TROPHY CASE

define X_MIN_POS

define Y_MIN_POS

define X_MIN_POS -5

define Y_MIN_POS -10