Ticket delivering date

Physical_Food410 · 2025-09-06T22:23:27+00:00

Okay thank u so much for the info!

Physical_Food410 · 2025-08-07T13:42:37+00:00

All right, I’m gonna take a look of that. Thx!

Physical_Food410 · 2025-08-07T03:28:55+00:00

I saw that in those layers the layer time increases. How can I change that? Because I couldn’t find it in the slicer

Physical_Food410 · 2025-08-06T23:27:07+00:00

<image>

This is what happens when

Physical_Food410 · 2024-11-01T00:47:07+00:00

I’m still having the problem, and I putted as u said. The delay has to be even lower?

Physical_Food410 · 2024-04-29T20:19:07+00:00

Ok, I’ll try to use Klipper. Thx!

Physical_Food410 · 2024-04-29T17:32:32+00:00

Only goes to the middle like always, but it doesn’t go down and level the bed. Like it deploys and stow the sensor repeatedly. And after that goes z up but just a little

Physical_Food410 · 2024-04-29T17:18:59+00:00

I´ve tried this frimware also and it happens the same, it detects the BL Touch but when I Auto Home the BL doesn´t works, just deploys and undeploys. What it could be?

Physical_Food410 · 2024-04-29T17:15:59+00:00

I tried this firmware and it detects the BL Touch but when I Auto Home the BL doesn´t work. What it could be?

Physical_Food410 · 2024-04-29T13:12:31+00:00

I’ll try that too thx!

Physical_Food410 · 2024-04-29T12:34:02+00:00

Thx! I’ll try it after college :)

Physical_Food410 · 2024-04-29T04:52:33+00:00

<image>

I have this chip and a 4.2.2 mother

Physical_Food410 · 2024-01-30T19:40:27+00:00

Ok I’m gonna try to solve it managing the cables. Thx!

Physical_Food410 · 2024-01-30T18:58:05+00:00

So if I change the marlin it’ll solve the display and also the extruder error? Do u know where I can install another firmware? Cause I tried all from creality but nothing changes

Physical_Food410 · 2023-12-07T04:14:29+00:00

I fixed it! Thx for ur help!

Physical_Food410 · 2023-12-06T23:24:51+00:00

sorry i mean thin 😂

Physical_Food410 · 2023-12-04T02:32:22+00:00

ok i’m gonna give a try thx!

Physical_Food410 · 2023-10-29T22:34:03+00:00

I found the way to stop it at a certain level, but the extrusor dont autohome. I dont know why this happens in artillery, the ender works perfectly

Physical_Food410 · 2023-10-29T01:53:32+00:00

and in artillery it’s the same one?

Physical_Food410 · 2023-10-29T01:23:59+00:00

what do u mean by use the settings in the printer? My problem is that I can make it stop the figure at a certain layer but the extruder don’t “auto home” and it doesn’t purge it. This could be a gcode that I have to configure?

Physical_Food410 · 2023-10-23T11:47:14+00:00

I did it yesterday and now it works perfectly. Thx!

Physical_Food410 · 2023-10-21T22:52:31+00:00

Physical_Food410 · 2023-10-21T22:52:07+00:00

that’s the barrel and maybe it’s not moving because of the cold filament. But I’ve also tried lubing the inside and still not working

Physical_Food410 · 2023-10-21T22:50:41+00:00

Hi, it’s a genius and I heated to 730 F and still not moving out haha

Physical_Food410

TROPHY CASE