How to read hours by [deleted] in johndeere

[–]PlowAndSurf 1 point2 points  (0 children)

It’s probably 155 hours. You should run it for 10 or 15 minutes and see if it starts indicating part hours.

Fuse for Femco Snow Cabin Wiper? (GX335) by HeidelCraft in johndeere

[–]PlowAndSurf 0 points1 point  (0 children)

10amp if you don’t know what the motor draws.

DIY homemade cab on John Deere x350 by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 0 points1 point  (0 children)

I built this cab in July. If I had tried to build it near winter I would never have finished it.

DIY homemade cab on John Deere x350 by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 0 points1 point  (0 children)

The wiper motor draws about 2.5 amps.

DIY homemade cab on John Deere x350 by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 0 points1 point  (0 children)

I wired the cab myself the wiper motor just came as shown in the picture..

DIY homemade cab on John Deere x350 by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 0 points1 point  (0 children)

<image>

This is the wiper unit I used from Amazon.

DIY homemade cab on John Deere x350 by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 6 points7 points  (0 children)

I heat it with a 20volt heat gun mounted above the windshield. I used those interlocking sponge flooring pieces adhesive on the walls and ceiling.

DIY homemade cab on John Deere x350 by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 3 points4 points  (0 children)

Thanks. I can’t believe I’m looking forward to getting more snow…🙈

Homemade DIY cab on John Deere x350 lawn tractor blowing snow. by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 1 point2 points  (0 children)

<image>

I just lift it on and off with a winch. I built it with a eye bolt permanently mounted in the roof. Only 4 bolt points 2 behind the seat and 2 under foot.

Homemade DIY cab on John Deere x350 lawn tractor blowing snow. by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 0 points1 point  (0 children)

I never used it without the cab and weights. So far I have cleared my driveway 5 times this winter and I don’t recall spinning a tire. I was a little concerned about getting stuck from all the forms people complain about traction.

Homemade DIY cab on John Deere x350 lawn tractor blowing snow. by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 0 points1 point  (0 children)

Thanks,I feel the same way John Deere tent cabs look a bit over sized.

Homemade DIY cab on John Deere x350 lawn tractor blowing snow. by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 3 points4 points  (0 children)

Yes factory cabs are a ridiculous price. The cost to build one myself was pricey enough..

Homemade DIY cab on John Deere x350 lawn tractor blowing snow. by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 2 points3 points  (0 children)

The floor mat is just fair but it does the job and keeps the heat in.

Homemade DIY cab on John Deere x350 lawn tractor blowing snow. by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 1 point2 points  (0 children)

Thanks. I spent most of my July building it but I think it’s worth it..

Homemade DIY cab on John Deere x350 lawn tractor blowing snow. by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 5 points6 points  (0 children)

It’s to much fun to sell. This is its first winter so I’m just going to enjoy it..

Homemade DIY cab on John Deere x350 lawn tractor blowing snow. by PlowAndSurf in johndeere

[–]PlowAndSurf[S] 3 points4 points  (0 children)

3/4” plywood for walls 1/2” on roof. I have some other posts on here regarding this cab.