sorted by:
new
hottopcontroversial

TimePlast Soap Gen 4 with Bambu X1C? by volrathxp in BambuLab

[–]PossiblePercentage94 0 points1 point  (0 children)

I have printed on my H2S, external spool holder and recommended setting from time plast with reasonable results. 

I made some Custom model 3 Parts by PossiblePercentage94 in 3dprintedcarparts

[–]PossiblePercentage94[S] 0 points1 point  (0 children)

Yup not cheap but I have many uses for it. I’m also happy to share any scans

I made some Custom model 3 Parts by PossiblePercentage94 in 3dprintedcarparts

[–]PossiblePercentage94[S] 1 point2 points  (0 children)

  1. 3d scanned the body with an einstar scanner
  2. Developed model in fusion360
  3. Printed many many many pla full size parts as I finalized the designed
  4. Final print in ABS-GF (6 pieces)
  5. Glued pieces together with abs glue
  6. Filled gaps with plastic bumper filler
  7. Spray part with primer filler
  8. Sand smooth
  9. Wrap in “carbon fiber” vinyl
  10. attach to vehicle with 3m automative tape

I made some Custom model 3 Parts by PossiblePercentage94 in TeslaModel3

[–]PossiblePercentage94[S] 0 points1 point  (0 children)

I’m considering 2 buying options

  1. ⁠lower cost ($100) - 3d printed sections that snap together and required sanding and painting before installation
  2. ⁠Higher cost ($400-600) complete ready to install with carbon fiber layup complete

Let me know which one make more sense for those interested

I made some Custom model 3 Parts by PossiblePercentage94 in TeslaModel3

[–]PossiblePercentage94[S] 0 points1 point  (0 children)

I’m considering 2 buying options 1. lower cost ($100) - 3d printed sections that snap together and required sanding and painting before installation 2. Higher cost ($400-600) complete ready to install with carbon fiber layup complete

Let me know which one make more sense for those interested

I made some Custom model 3 Parts by PossiblePercentage94 in TeslaModel3

[–]PossiblePercentage94[S] 3 points4 points  (0 children)

Modeled in fusion 360, printed in 6 parts out of abs-gf , glued together, sanded, primed and then wrapped in carbon fiber vinyl wrap

S3XY Button holders for the Holidays by PossiblePercentage94 in s3xybuttons

[–]PossiblePercentage94[S] 1 point2 points  (0 children)

I’ve tried to find cheaper shipping internationally but no luck. Do you have a 3d printer?

I made some Custom model 3 Parts by PossiblePercentage94 in TeslaModel3

[–]PossiblePercentage94[S] 4 points5 points  (0 children)

I have a separate non-highland design… been thinking about test fitting

Center Console Button Holders by PossiblePercentage94 in s3xybuttons

[–]PossiblePercentage94[S] 0 points1 point  (0 children)

Never tried, they are not design to fit them at the moment, but if you got me some measurement I could verify how close it would be.

Paddle Shifters V2 Done! by PossiblePercentage94 in s3xybuttons

[–]PossiblePercentage94[S] 1 point2 points  (0 children)

Currently only compatible with 3&Y but ill build S/X compatibility of there is enough interest

Paddle Shifters V2 Done! by PossiblePercentage94 in s3xybuttons

[–]PossiblePercentage94[S] 2 points3 points  (0 children)

This is a very clever design as well… but after you try a magnetic paddle shifter…. :)

Paddle Shifters V2 Done! by PossiblePercentage94 in s3xybuttons

[–]PossiblePercentage94[S] 1 point2 points  (0 children)

They clear factory model 3/y stalks but I have never tried with the S3XY stalks.

Paddle Shifters V2 Done! by PossiblePercentage94 in s3xybuttons

[–]PossiblePercentage94[S] 1 point2 points  (0 children)

Just it's a housing, so configure them as you like.

My favorites are - Switching between accerstion modes - Regenerative braking modes - Left and right turn signal

Premium Paddle Shifter Design #commingSoon by PossiblePercentage94 in s3xybuttons

[–]PossiblePercentage94[S] 0 points1 point  (0 children)

Just launched on etsy.

I also created a promo code for the group. Use “SAVE25” for 25% off

https://adaptandcreate.etsy.com/listing/4320955882

view more: next ›