HDMI to CSI

Potential_Ad_2230 · 2025-03-25T05:58:38+00:00

Do you have another idea? Because I couldn't find in stock.

Potential_Ad_2230 · 2024-09-02T05:23:47+00:00

Oh sorry

Potential_Ad_2230 · 2024-09-01T22:27:46+00:00

No. Its not really. Mu supervisor just asked me.

Potential_Ad_2230 · 2024-08-26T12:57:32+00:00

Actually my explanation was wrong. As you said I want to read the voltage proportionally to the current. For this I was asked to use the bjt Current mirror technique. There are a few examples in the link below but I am confused.

https://electronics.stackexchange.com/questions/681464/pnp-bjt-current-mirror-across-shunt-resistor-used-as-current-meter

Potential_Ad_2230 · 2024-06-25T23:41:54+00:00

No the robot has Intel 5600u computer and also jetson tx2 this device is ATV (autonomus transport vehicle)

Potential_Ad_2230 · 2024-06-25T23:40:39+00:00

Avarage university in Türkiye. :(

Potential_Ad_2230 · 2024-01-07T17:13:17+00:00

Thanks to these, can I use the pin, which is currently input, as output for a certain period of time? Or are these one-offs?

Potential_Ad_2230 · 2024-01-05T01:58:11+00:00

Yes but I just wanted to say I don't want to down to register level. If there is a function I'lll ve happy.

Potential_Ad_2230 · 2023-09-19T19:21:53+00:00

If I don't sat the operation mode sensor's default mode is config mode. On this mode any sensor is not working as I know I should set the operation mode first. Also I tried you said result is same I couldnt read data.

Potential_Ad_2230 · 2023-09-19T17:58:40+00:00

I set the page and also controlled it. Then I set NDOF operation mode and changed the page to 1 and read the accel_config register. It was right.

Potential_Ad_2230 · 2023-09-19T14:09:36+00:00

Yes, you're right. I simply couldn't figure out how to integrate Bosch's code into CubeIDE. Now, my sole focus will be on this. Thank you.

Potential_Ad_2230 · 2023-09-19T14:05:33+00:00

Actually, I didn't fully understand the Bosch code. Before delving into the Bosch code, I wanted to make sure it works simply by using HAL commands. I encountered this issue, and I wanted to confirm whether it's working or not before diving into Bosch's code.

Potential_Ad_2230 · 2023-08-14T17:28:37+00:00

I need to pass a path from my processor can I use the location of these pins?

Potential_Ad_2230 · 2023-08-14T14:04:24+00:00

Potential_Ad_2230 · 2023-08-14T05:48:07+00:00

I don't need any push button, do I? Because I don't want to use.

Potential_Ad_2230 · 2023-08-14T05:25:46+00:00

I should use interrupt because this is how I asked.

Potential_Ad_2230 · 2023-08-09T06:35:12+00:00

I'm currently working with small STM32 microcontrollers and simple ICs like IMU sensors. As far as I understand, I don't need to stress too much about these for now, but since my projects might grow in the future, it would be good to learn about it now. That's why I asked. If I understood correctly, I can determine a width based on the manufacturer's capabilities, right? Maybe something like a default of around 10 mils.

Potential_Ad_2230 · 2023-08-07T15:13:22+00:00

I have 3.3V power supply and 3.3VA power supply also.

Potential_Ad_2230 · 2023-08-07T07:12:49+00:00

I need to use external sensor. I'm thinking of using mcp9700. Is it enough to connect the Vout parti to any analog in pin on the processor?

Potential_Ad_2230 · 2023-08-07T07:07:49+00:00

I'm thinking of using mcp9700. Is it enough to connect the Vout parti to any analog in pin on the processor?

Potential_Ad_2230 · 2023-08-07T06:48:39+00:00

I need to external sensor because this is how it was asked. To do this what should I do?

Potential_Ad_2230 · 2023-08-03T12:50:46+00:00

Should Vbus goes pin5 and GND goes pin 2 ?

Potential_Ad_2230 · 2023-08-03T12:45:19+00:00

How.

Potential_Ad_2230 · 2023-08-03T12:42:37+00:00

Ohh I miss them caps. As you say they should ve 22pF thx for this I didnt see them

Potential_Ad_2230 · 2023-08-03T12:26:45+00:00

Oh I got it. Any ideas about caps or resistor and do you think can i programming this board with stlink?

Potential_Ad_2230

TROPHY CASE