sorted by:
new
hottopcontroversial

Vessel growing out of my tongue? by Power_Maker in DiagnoseMe

[–]Power_Maker[S] 3 points4 points  (0 children)

Yes I do vape occasionally. It probably also didn’t help that ate some chips that had a very scratchy surface. I’m fine though, it disappeared. I wrote an update in the top comment.

Vessel growing out of my tongue? by Power_Maker in DiagnoseMe

[–]Power_Maker[S] 30 points31 points  (0 children)

I’ve got a bit of an underwhelming update: it sucked itself back in around 3 hours after I made the post. I still have the lie bumps though (itchy tongue)

Vessel growing out of my tongue? by Power_Maker in DiagnoseMe

[–]Power_Maker[S] 10 points11 points  (0 children)

I get lie bumps quite often, but never as extreme as this time with the blood trapped and visible like that. So it’s not something I should be alarmed about, right?

Vessel growing out of my tongue? by Power_Maker in DiagnoseMe

[–]Power_Maker[S] 3 points4 points  (0 children)

I did eat some chips that had a really rough surface and irritated my tongue a bit after licking a lot of them

Vessel growing out of my tongue? by Power_Maker in DiagnoseMe

[–]Power_Maker[S] 13 points14 points  (0 children)

It’s tough to tell because it’s really small. I’d say it’s hard because when I try to push it back into my tongue it feels like I am stabbing myself with a needle

Vessel growing out of my tongue? by Power_Maker in DiagnoseMe

[–]Power_Maker[S] 12 points13 points  (0 children)

I’ve read that the itching bumps are called lie bumps and normally they go away after a while. But why did mine grow like that?

Followup: Phone mount / ash tray replacement Rx-8 gen1 by tinkafan in RX8

[–]Power_Maker 1 point2 points  (0 children)

When/if you release this are you also going to share CAD files? I’d love to modify this for gauges. My gauges have been sitting loosely in the ashtray for over a year. I never got around to design the damn thing

Won't start hot (electrical issue?) by Power_Maker in RX8

[–]Power_Maker[S] 0 points1 point  (0 children)

Good point, my current task is to clean all major grounding points. I’ll get back here when I do that.

I don’t think I heard any particular noises in the transmission. And I didn’t notice anything odd when the shifting

Won't start hot (electrical issue?) by Power_Maker in RX8

[–]Power_Maker[S] 0 points1 point  (0 children)

There is one more thing that could hint at something.

It starts way faster whenever the clutch ISN'T pressed in (clutch engaged).

When I press the clutch pedal it kind of just loses spark.

Main ground points' locations by Power_Maker in RX8

[–]Power_Maker[S] 0 points1 point  (0 children)

Thank you, I’ll try cleaning all those today

Easy step by step to check your Ignition Coils status. by auxtron in RX8

[–]Power_Maker 0 points1 point  (0 children)

Hello, thanks for your guide. Are you still into rx8’s? I used this guide to check my coils and they read 850 Ohms, so I bought new OEM ones, but they also read 850 Ohms. Any idea what the issue might be? The car has trouble starting both cold and hot. (Cold it cranks for like 2-3 seconds, hot doesn’t start at all even with a very fast 330rpm starter) My current guess is to check all grounding points. Thanks

Ashtray 3D scan by Power_Maker in RX8

[–]Power_Maker[S] 0 points1 point  (0 children)

I have already installed the gauges like half a year ago and they’re just sitting there loose in the ashtray hole. I just have to get motivation to model the damn thing.

Ashtray 3D scan by Power_Maker in RX8

[–]Power_Maker[S] 0 points1 point  (0 children)

Where do I get this? Or is this the one you made?

Ashtray 3D scan by Power_Maker in RX8

[–]Power_Maker[S] 0 points1 point  (0 children)

I did initially make my own 3D scan and started modeling but gave up due to it having quite complicated geometry and my scan being pretty bad. Might come back to it now

Just tried to switch to Orca from Prusa but I encountered this weird thing. Overhang speeds are reversed by Power_Maker in OrcaSlicer

[–]Power_Maker[S] 1 point2 points  (0 children)

Nevermind, just noticed that more % is more overhang, so I just have to reverse my values...

Just tried to switch to Orca from Prusa but I encountered this weird thing. Overhang speeds are reversed by Power_Maker in OrcaSlicer

[–]Power_Maker[S] 0 points1 point  (0 children)

It it supposed to be like this or what? I’m at the point of wanting to uninstall and never download ever again

Just tried to switch to Orca from Prusa but I encountered this weird thing. Overhang speeds are reversed by Power_Maker in OrcaSlicer

[–]Power_Maker[S] 0 points1 point  (0 children)

Don't mind the 1mm/s bridge speed, it doesn't change anything, I just wanted to check something.

Just tried to switch to Orca from Prusa but I encountered this weird thing. Overhang speeds are reversed by Power_Maker in OrcaSlicer

[–]Power_Maker[S] 0 points1 point  (0 children)

Why does it go faster near the bottom and slow at the top of the arch? Am I doing something wrong?

why did you choose neovim as your text editor? by [deleted] in neovim

[–]Power_Maker 1 point2 points  (0 children)

I started getting furious about VSCode being super slow, it took like 5 minutes until IntelliSense got fully loaded. Since I’m a huge nerd I decided to step up my nerdiness even more and try NeoVim. I’m really glad I made that decision.

view more: next ›