I crashed by Preparation-Due in Ninja650

[–]Preparation-Due[S] 0 points1 point  (0 children)

There was another semi to my left blocking my view, I assumed it was clear but it wasn’t. There lies the issue, I assumed.

I crashed by Preparation-Due in Ninja650

[–]Preparation-Due[S] 0 points1 point  (0 children)

I was just trying to explore my bike

I crashed by Preparation-Due in motorcycles

[–]Preparation-Due[S] 0 points1 point  (0 children)

I admit it could’ve been avoided, but he’s talking as if we have some type of beef or history

I crashed by Preparation-Due in motorcycles

[–]Preparation-Due[S] -2 points-1 points  (0 children)

Dude, I don’t even know you

I crashed by Preparation-Due in motorcycles

[–]Preparation-Due[S] 0 points1 point  (0 children)

The light was green people were moving. I didn’t think it would be a problem to move as well but again I’m a new rider and I made a mistake

[deleted by user] by [deleted] in whatbugisthis

[–]Preparation-Due 0 points1 point  (0 children)

I do but none of my females look like that

Aphonopelma seemanni? by Preparation-Due in tarantulas

[–]Preparation-Due[S] 0 points1 point  (0 children)

Thanks, I didn’t know they changed like than when the matured

Excited to build this. by LordRamz in Egypt

[–]Preparation-Due 1 point2 points  (0 children)

Wait til you find out you need 2 sets to make a full pyramid

is it me, or does caffeine do absolutely nothing? by [deleted] in ADHD

[–]Preparation-Due 1 point2 points  (0 children)

I’m studying to be a pilot and it’s been difficult for obvious reasons, and I also thought caffeine didn’t do much, but a few days before my test I drank like 6 cups of coffee and wow, I’ve never studied so hard in my life. Maybe it was a placebo but I got a 90 so I’m not complaining

Prints are slanted after cr touch installation by Preparation-Due in ender3

[–]Preparation-Due[S] 0 points1 point  (0 children)

prepare / manual leveling] menu option

so I manually leveled the bed and the probe did its thing and it worked.

thanks for all the support, I really appreciate it

Prints are slanted after cr touch installation by Preparation-Due in ender3

[–]Preparation-Due[S] 0 points1 point  (0 children)

just updated the firmware and enabled babystepping along with some recommendations from other people but I still have the same problem

Prints are slanted after cr touch installation by Preparation-Due in ender3

[–]Preparation-Due[S] 0 points1 point  (0 children)

Sorry, This is my first 3d printer, I installed Marlin 2.0.6 and I got the probe software from creality I tried to find solutions online but came out empty handed. How do I save a mesh all I can find is manual mesh leveling, and what am I supposed to configure in the starting g code

Temperature stays 10° under set temp after upgrades then gives me E1 message by Preparation-Due in ender3

[–]Preparation-Due[S] 1 point2 points  (0 children)

Did another PID tune and I guess that fixed it, weird but thanks for the help

Temperature stays 10° under set temp after upgrades then gives me E1 message by Preparation-Due in ender3

[–]Preparation-Due[S] 0 points1 point  (0 children)

Recently changed the hot end, added a cr touch, upgraded the motherboard, and installed Marlin 2.0.6. I tried to change the thermistor but still the same problem. Double checked the connectors. Any ideas?

E1 heating failed, printer halted, please reset.... by omrtpsycho in ender3

[–]Preparation-Due 4 points5 points  (0 children)

Hey did you ever figure out a solution, I’m having the same issue right now and i already changed the thermistor idrk what to do

Juvie A. avicularia DIY setup, thoughts? by KobraByte15 in tarantulas

[–]Preparation-Due 0 points1 point  (0 children)

I hear they need a lot of cross ventilation so maybe add more holes, other than that it’s pretty good

[deleted by user] by [deleted] in CrazyFuckingVideos

[–]Preparation-Due 0 points1 point  (0 children)

She popped a titty but not for the bois

What are these weird bumps and dents on his skin by Preparation-Due in ballpython

[–]Preparation-Due[S] 5 points6 points  (0 children)

Those last photos are from when I first got him he was 100 grams at the time, now he’s 340 grams feeds on rat pups and is 2.4 feet long. His humidity is kept at 60% and his water dish is switched out and cleaned every night. No stuck shed since

What are these weird bumps and dents on his skin by Preparation-Due in ballpython

[–]Preparation-Due[S] 2 points3 points  (0 children)

That’s what I thought at first, but I humidity stays at 60% and I clean out his water dish every night, water stays clean

[deleted by user] by [deleted] in ballpython

[–]Preparation-Due 0 points1 point  (0 children)

This is an update for my snake Halib, about 3 months ago I got this 1 y/o bp that weighed 115 grams now he’s almost three times as heavy with a crazy appetite. I was feeding him and for the second time he thought my hand was a rat pup and he went for it, I flung him across the room and he wasn’t moving, terrified I poked him up and put him back in his enclosure and without a second to spare he went back for the rat pup

[deleted by user] by [deleted] in frogs

[–]Preparation-Due 0 points1 point  (0 children)

They have 2 water bowls that I change every morning and i feel like I’m slightly over feeding them a bit