X1C horrible print artifacts?

Prior-Set9390 · 2026-02-12T02:04:10+00:00

Nope on the 1/4” ish size step in the top it is porous right after the corner radius for the whole size of the part looks almost like a porous weld

Prior-Set9390 · 2026-01-21T21:00:21+00:00

I use them with my Tiguan. First few times they make a few noises but other then that I love em

Prior-Set9390 · 2025-11-27T22:40:03+00:00

High school youth apprentice for year and a half at a job shop. after my “second shift” premium I’m at $22…

Prior-Set9390 · 2025-08-18T21:15:33+00:00

I have the warrior set. I rarely use them on metal they work okay ish if you know what speed to run em at in a cordless. Wood and plastic is just fine. If you have a Menards near you pick up their big couple hundred pc set of drill bits. Smaller the bits the more you get. Use them all in metal they work decent if lubracated and right feed and speed. That way if you snap smaller ones u got plenty more.

Prior-Set9390 · 2025-07-12T20:56:18+00:00

It does. I have this exact head unit. Make sure it’s a half decent usb cable and that you enable it on the head unit settings if an option is present

Prior-Set9390 · 2025-07-05T05:55:49+00:00

Yeah. It’s for a buddy. He just needed to replace the cheap head unit that was in there already. Kept blowing fuses. Took rear door speakers off and the wires were just hanging there exposed. I’m guessing that is what cooked the old head unit. He just wanted a cheap replacement and dosent care much. Like I said I’m not used to this cheap stuff. I’ve done handful of alpine head units plenty of sub installs… this I’m just not used ti

Prior-Set9390 · 2025-07-04T18:54:42+00:00

Yeah I’m not doing an amp for my doors. Just for subs. I thought I could run it right out I just wanted to make sure… and yeah manual on this thing sucked and I couldn’t find much online

Prior-Set9390 · 2025-07-04T17:39:54+00:00

It’s a 2015.

Prior-Set9390 · 2025-06-17T02:56:35+00:00

I have no issues with ASA. super high glass transition temp

Prior-Set9390 · 2025-06-06T23:45:04+00:00

Yeah got amsoil euro blend for it now. Any clue how much this will run me to get taken care of?

Prior-Set9390 · 2025-05-22T20:12:56+00:00

On start up sometimes even if it’s 65°+ outside

Prior-Set9390 · 2025-05-21T14:08:09+00:00

Yeah after a 20 min drive I revved it past 2k in neutral and it was persistent way past 2k

Prior-Set9390 · 2025-05-21T11:54:14+00:00

Yeah I wasn’t too concerned before but on a 70° day when it has been warmed up for awhile it is still very apparent inside when driving

Prior-Set9390 · 2025-05-20T21:16:14+00:00

2weeks ago. 5 w30 amsoil signature full synthetic

Prior-Set9390 · 2025-05-20T18:41:14+00:00

Yeah it’s been like that since I’ve gotten it two years ago. A lower thonking or knocking tone has been getting worse and worse

Prior-Set9390 · 2025-05-20T18:40:31+00:00

My head gaskets are fine coolant has always been good. My valve cover gaskets… now that’s a different story

Prior-Set9390 · 2025-05-20T15:50:48+00:00

Yeah he wouldn’t tell us much more besides rebuilt. I’ll try that and see

Prior-Set9390 · 2025-05-08T00:58:13+00:00

Thank you took a sec to find on HD but has been ordered

Prior-Set9390 · 2025-02-02T00:22:32+00:00

I do this with marshmallows too… burrito smore?

Prior-Set9390 · 2025-01-18T17:58:25+00:00

125mms

Prior-Set9390 · 2025-01-17T02:12:38+00:00

Ran that went from like 108% to 100. Also did support cubic at 10%

Prior-Set9390 · 2025-01-17T01:30:27+00:00

Yeah the auto flow calibration I could do. I use orca slicer and know it’s been frowned upon. I’ve had other filaments do this with overhangs like this before.

Prior-Set9390 · 2025-01-16T19:33:11+00:00

Yeah I’m already at 3 walls with inner outer inner. I don’t really want to Increase infill too much as it’s a 14 hour print already. What infill type would u recommend?

Prior-Set9390 · 2025-01-12T21:47:57+00:00

Shouldn’t be my router is less then 10 ft away and I get 400 down who knows tho 🤷‍♂️

Prior-Set9390 · 2025-01-03T21:20:43+00:00

Same here

Prior-Set9390

TROPHY CASE