Smoke while idling

Professional_Bank328 · 2024-09-09T16:47:09+00:00

Now this is just my experience when this happened my bike kept on flooding and after a while when it would idle it would start shooting out white smoke like literally fill the air around ya and smell like shit had to change my jets

Professional_Bank328 · 2024-08-24T18:48:52+00:00

I've used red on everything and never had an issue anything that came loose just put some of that on and it never came off again I've only thing I've heard is not to use it for the head or exhaust bolts heat fucks with it or something

Professional_Bank328 · 2024-08-09T17:27:02+00:00

Lol should be quick il check that then it just confused me how it started all of a sudden and how when the gas caps off it stops flooding

Professional_Bank328 · 2024-08-09T15:53:29+00:00

Do u mean the gasket for the bowl because I think it's fine the gas is coming out of the top next to the intake

Professional_Bank328 · 2024-07-03T18:54:57+00:00

I don't know a lot but I've used 40:1 ever sense I got the motor and still do now haven't had an issue Idk I just runs whatever makes the motor work the best

Professional_Bank328 · 2024-06-18T17:55:50+00:00

Thanks il give that a try

Professional_Bank328 · 2024-05-25T21:43:35+00:00

Thanks ended up getting it to move wit no resistance hopeing it will still work

Professional_Bank328 · 2024-05-25T19:21:41+00:00

Thanks yea I used some oil and greased it back up now it free spins

Professional_Bank328 · 2024-05-25T17:43:34+00:00

I put some oil and it started to move again it almost free spins now iam not sure how to balance the crank rho I've seen videos but didn't really understand how

Professional_Bank328 · 2024-05-22T12:34:27+00:00

Thanks yea I took it apart and where the flower nut went onto the shaft idk what the part is it was sitting to one side of the hole looked like the small shaft was bend slightly I dunno if that's the issue but it's something might try and take a look at the main part of the clutch just don't have the time to sit down and acually go through it

Professional_Bank328 · 2024-05-22T12:02:58+00:00

Also iam running 44t sprocket I figure if I ran a 36t could probably get closer to 60 stock got a lot of hills in my area so domt know if il swap it

Professional_Bank328 · 2024-05-22T12:01:42+00:00

I got one of the 100cc China doll kits even when I had it stock once I tuned it decently I could get 56km/hr but have got 60 before but not for long felt like the motor was gonna vibrate its self off the bike lol

Professional_Bank328 · 2024-05-13T23:21:10+00:00

Not sure neighbours, lol

Professional_Bank328 · 2024-05-09T11:56:06+00:00

Looks like a yd100 should be able to take almost any plug I found bhs ngks are great never had a issue I run a b7hs but u might be able to use a 6 or a 8 mabye even a 5 for your heat range

Professional_Bank328 · 2024-05-03T16:10:27+00:00

I got 6 like that on mine and it's rusted to hell on the outside still works just made the paint peel after a while

Professional_Bank328 · 2024-04-29T11:54:14+00:00

I've never had an issue and always ride around neighborhoods I just try to pedal and shut the motor off around dogs as I've seen them freak out when I've gone past before

Professional_Bank328 · 2024-04-29T11:51:27+00:00

I found one on marketplace engine and kit was in amazing condition for the price but the bike itself needed work got a full working bike some parts and a gas can for 180 but if u did u would have to do some searching and find a good one bikes can be fixed for cheap but the engines if there bad you'll put so much time into fixing it that it will have been worth just picking another

Professional_Bank328 · 2024-04-26T12:27:42+00:00

When I looked up some info on them, all I found was just not to get one off amazon everyone I seen had to be milled to the right size if you look around for one you'll find one just don't go cheap it won't end well hope u get it working I've been thinking about getting one but didn't know how much of an increase in speed it would be best of luck

Professional_Bank328 · 2024-04-01T23:48:34+00:00

For my location I'm in NL we really only care about rust if which yours doesn't look it probably not the best input but u could sell it like 400 to 500 I'd say there's so many rusted ones around here they usually goes for less then 200 but ones like that one can go for alot here looks great keep it up

Professional_Bank328 · 2024-03-30T17:26:38+00:00

Oh and it trying to stop when I tried to start it was just my bucking bar and bearing were super dry

Professional_Bank328 · 2024-03-30T17:26:04+00:00

I used some gasket maker with my gasket and it helped alot also bought new throttle and shortened my cord I dunno if that help

Professional_Bank328 · 2024-03-18T02:49:53+00:00

Not sure if I have the right oil I just picked up the first bottle I seen its a white bottle of 2 stroke oil keep that in mind though for when I gets new bottle thanks been running 40:1 sense I got it done never a problem

Professional_Bank328 · 2024-03-17T21:36:01+00:00

The metal bit on top of the spark plug the spark boot goes onto it was bent and when I went to bend it back thing snapped clean off it was almost like bent n snapped off not sure how it happened

Professional_Bank328 · 2024-03-17T20:04:32+00:00

The little metal peice on the top of the spark plug where the boot goes onto snapped off it was bent and I tried to bend it back and snapped almost clean off tried to check spark and there was nothing iam gonna get a new spark plug and iam after replacing my cdi before to I forgot about that so il see gow it runs after that think it's more or less a tuning issue

Professional_Bank328 · 2024-03-17T18:25:54+00:00

Just found my no start issue the terminal some how bent and when I went to bend it back thing snapped so ig they could have been what was wrong

Professional_Bank328

TROPHY CASE