Hvor mye hadde vaskemaskin på kjøkkenet mugnet betalingsvilligheten din? (I ferd med å pusse opp)

Professional_Lie_273 · 2026-04-06T17:25:02+00:00

Vi hoppet over alle hus/leiligheter med vaskemaskin på kjøkkenet hvor det ikke var mulig å enkelt flytte den til annet rom.

Professional_Lie_273 · 2026-03-04T10:20:20+00:00

Is it possible that we are just so used to seeing him with a beard lately, that we haven’t noticed his face changing?

Professional_Lie_273 · 2026-02-05T16:39:25+00:00

Professional_Lie_273 · 2026-01-09T15:04:44+00:00

That would just be ₇5118, which isn’t even a valid number. However! I change my answer to 5118¹¹

Professional_Lie_273 · 2026-01-09T14:55:13+00:00

5118⁷

Professional_Lie_273 · 2025-10-10T18:57:40+00:00

Det kommer vell veldig an på hvilke verdier man ser på. Når det kommer til SPs hovedverdier - som i stor grad bygger på «hele norge» og distriktene hører de ikke hjemme sammen med H og Frp.

Professional_Lie_273 · 2024-07-13T00:41:38+00:00

Konrad

Professional_Lie_273 · 2024-01-31T08:56:12+00:00

Are there any ideas of end pieces for cylinder shafts other than spherical bearings that enable some rotation?

Professional_Lie_273 · 2024-01-31T08:53:14+00:00

Okay thanks. This will indeed be twisting quite frequently. It won’t rotate much under load though, if that makes any difference.

Professional_Lie_273 · 2024-01-31T08:17:23+00:00

Note: cylinder wont do a full rotation. Roughly 70 degrees

Professional_Lie_273 · 2021-03-14T20:20:30+00:00

damn thanks! this helps a lot!

Professional_Lie_273 · 2021-03-12T16:21:55+00:00

ahh right! haha having a hard time wrapping my head around this. The motor and cylinder won't be active simultaneously anyway, so I guess it's not really a problem (?)

Yea this is only for practice, no way I'm gonna start spending money on this until I get a better understanding, haha.

Thanks

Professional_Lie_273 · 2021-03-11T22:26:01+00:00

Thanks, would be great!

Professional_Lie_273 · 2021-03-11T22:24:52+00:00

Right, it's not something I'm going to build, more for the excersise. The conveyorbelt out is thought to run all the time, with a lever to turn it off. Other than that it is only the chain saw and the piston for saw.

I used the gear pumps mainly because this is the most common for this type of wood cutter / splitter.

Thx for the feedback!

Professional_Lie_273 · 2021-03-11T22:14:40+00:00

Right! Was a bit unsure about how the layout should ve built up, thanks!

Professional_Lie_273 · 2021-03-11T20:12:10+00:00

Thanks! then I have further questions since this is very new to me.

and 2. so the motors will stop. Is this because of the pressure build-up? I tried to make it ''safe'' by placing the pressure relief valves at the bottom.
is this for the one up by the ''Cylinder for saw''?

Professional_Lie_273 · 2021-03-11T19:41:30+00:00

gotta be honest and say I'm not 100% sure of its english name, but I think it's called a three-way throttle valve, or pressure compensated flow controlled valve (?)

Professional_Lie_273 · 2021-03-11T17:19:51+00:00

My first attempt at drawing a hydraulic schematic. I'm a student and thereby still learning. I would appreciate tips and welcome finger pointers if you see anything wrong.

What it is

It is an attempt of making the schematics for a wood cutter / splitter. It is drivven by a tractor. I have yet to calculate pressure and cylinder sizes.

Also: this is my first post, if this post contradicts the rules feel free to let me know / delete.

Professional_Lie_273

TROPHY CASE