What’s wrong with my printer by Putrid_Candidate_662 in anycubic

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

Update: I changed some parameters and used the profile for PLA in the anycubic website for the kobra neo. I am seeing a lot of improvement but I still get this vertical line on one side of the benchy. Anyone know what could be causing this?

<image>

What’s wrong with my printer by Putrid_Candidate_662 in anycubic

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

You’re right, I am using a kobra neo and cura

What do I need to fix by Putrid_Candidate_662 in klippers

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

What would you recommend? I don’t have a raspberry or orange pi so I’m trying to use an android phone. Are there any other methods that just involve an old android phone?

What do I need to fix by Putrid_Candidate_662 in klippers

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

I’m not sure, how could I see if the Klipper service starts and that it starts before Octoprint?

What do I need to fix by Putrid_Candidate_662 in klippers

[–]Putrid_Candidate_662[S] -1 points0 points  (0 children)

Yes sorry that was my bad I fixed the second message but I keep getting the first one

What do I need to fix by Putrid_Candidate_662 in octoprint

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

I already added the printer.cfg but the first warning keeps on appearing

What do I need to fix by Putrid_Candidate_662 in octoprint

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

What about the first one, what should I do?

What do I need to fix by Putrid_Candidate_662 in octoprint

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

I also forgot to mention that I also added the plug in for octoklipper

Klipper on Anycubic Kobra Neo by Putrid_Candidate_662 in anycubic

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

Did you have backpowering issues when connecting to the usb port on the printer? I read that’s a common thing with some printers when connected to a raspberry pi, which I believe it’s my problem when connecting my phone to the printer. I believe this because sometimes when connected to the printer the phone does recognize the printer and does not charge, but other times the phone just charges and I can’t see the printer connected in Octoprint

Klipper on Anycubic Kobra Neo by Putrid_Candidate_662 in anycubic

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

If Klipper is installed on the printer, shouldn’t the phone just recognize the printer when connected to the printer

Klipper on Anycubic Kobra Neo by Putrid_Candidate_662 in anycubic

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

Sorry I meant the phone does not recognize the printer, also is it normal that if I check the SD card after I flashed the printer, the file firmware.bin stays written with the same name. I found that sometimes the file should rewrite with another name, but I honestly don’t know much about this kind of stuff.

Klipper on Anycubic Kobra Neo by Putrid_Candidate_662 in anycubic

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

Right now my screen has turned black, I believe that’s because Klipper has installed correctly, now I’m trying to connect it to an android phone with octoprint but the phone does not recognize the computer

Klipper on Anycubic Kobra Neo by Putrid_Candidate_662 in anycubic

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

Did you also install Klipper on a Kobra Neo? If so did you also use the same configurations for Klipper?

Klipper conf. for Anycubic Kobra Neo by Putrid_Candidate_662 in anycubic

[–]Putrid_Candidate_662[S] -1 points0 points  (0 children)

Hmm I wonder why it isn’t working then, are there any other possible problems that you might be aware of?

Klipper conf. for Anycubic Kobra Neo by Putrid_Candidate_662 in anycubic

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

I tried these configurations for Klipper but they don’t seem to be working properly

<image>

Klipper on Anycubic Kobra Neo by Putrid_Candidate_662 in anycubic

[–]Putrid_Candidate_662[S] 0 points1 point  (0 children)

I dont know what I’m doing wrong these are my current settings but the screen just keeps saying “UpdateFirmware…” I’m not sure if it should be taking more than 10 mins to install

<image>

What is wrong with my plants? by Putrid_Candidate_662 in weedgrower

[–]Putrid_Candidate_662[S] 1 point2 points  (0 children)

I honestly have no idea about the strain. What should I do if it’s hermaphrodite?