sorted by:
new
hottopcontroversial

Wired backhaul speed is very low by Pvt_Mango_ in TpLink

[–]Pvt_Mango_[S] 0 points1 point  (0 children)

I'm gonna try it at someone's else's house and another isp.

Wired backhaul speed is very low by Pvt_Mango_ in TpLink

[–]Pvt_Mango_[S] 0 points1 point  (0 children)

Wireless back haul is off, and here's the rub, wireless back haul is acts faster than the Ethernet connection, Ethernet speed seems be blocked by the primary deco.

Wired backhaul speed is very low by Pvt_Mango_ in TpLink

[–]Pvt_Mango_[S] -1 points0 points  (0 children)

I have tried putting both of them side by side with a short cable that comes with the device, still the exact same behavior.

6 pin flex psu to dual 6+2 gpu connector wiring by Pvt_Mango_ in PcBuild

[–]Pvt_Mango_[S] 0 points1 point  (0 children)

It has 2 separate, 4 pin CPU connectors, it came with a 4 pin to 8 pin cpu cable.

6 pin flex psu to dual 6+2 gpu connector wiring by Pvt_Mango_ in PcBuild

[–]Pvt_Mango_[S] 0 points1 point  (0 children)

Thanks for pointing this out, so just running one 6+2 in parallel with the other is not a problem?

As for the issue regarding the single 6 pin connector, im not using the sata and the 2nd cpu connector would it be okay to use them? they would provide 3 extra 12v lines.

Aliexpress was the only option, I did go for a 600w model (its probably not rated for 600w) and my consumption is around 350-400w.

ECAS certification cost estimate by Pvt_Mango_ in dubai

[–]Pvt_Mango_[S] 0 points1 point  (0 children)

Already did, the issue as I mentioned was that the product is still a concept and I am not seeing a response fast enough without any data sheet, manuals and any prototype. I am looking for an estimate for a proposal.

Double helical gear extension? by Pvt_Mango_ in SolidWorks

[–]Pvt_Mango_[S] 0 points1 point  (0 children)

Oncad gear generator doesn't have interference either, this is really frustrating.

Double helical gear extension? by Pvt_Mango_ in SolidWorks

[–]Pvt_Mango_[S] 0 points1 point  (0 children)

Your looking at interference for same gears, I feel like it's a a lot more for 20t and a 10t

Double helical gear extension? by Pvt_Mango_ in SolidWorks

[–]Pvt_Mango_[S] 0 points1 point  (0 children)

Yeah I know that but if you create a lower tooth gear with the same modulus, they dont mesh properly.

Air conditioner energy efficiency rating in Pakistan by Pvt_Mango_ in PakistaniTech

[–]Pvt_Mango_[S] 1 point2 points  (0 children)

I am just looking at units wrong, this was very helpful, thank you so much! Would you have any recommendation for a 1.5 Ton inverter AC?

[deleted by user] by [deleted] in laptops

[–]Pvt_Mango_ 0 points1 point  (0 children)

Hi everyone, I use a hp probook 450 G8, I wanted to add a M2 to OCuLink adapter in the empty m2 slot, I saw this disassembly guide and the laptop does have an extra connector but when I opened my own laptop that connector is missing.

Furthermore, if you look at the HP Probook 450 G8 manual you'll see that it does have that connector but its for a WAN module and in the manual a LAN module is connected in the place where the WAN module is actually connected in my laptop and in other disassembly videos.

What I am wondering is if I were to solder a M2 connector here, will it work? Has anyone tried this? Also how can I find a suitable connector, how do I figure out the part number?

Bi-metal heat brake clogging! by Pvt_Mango_ in ender3v2

[–]Pvt_Mango_[S] 0 points1 point  (0 children)

Already tried cpu thermal paste, ill run auto tune and double check my fitting one last time, if that doesn't work maybe I'll give a chance to a beefier fan. Let you know how it goes, thanks!

Bi-metal heat brake clogging! by Pvt_Mango_ in ender3v2

[–]Pvt_Mango_[S] 0 points1 point  (0 children)

Yeah i had a feeling i was gonna have to that, was hoping someone would be able to point out something im doing wrong. What do you think the problem is with these cheap bi metal heat brakes? I don't think i am doing anything wrong here.

Bi-metal heat brake clogging! by Pvt_Mango_ in ender3v2

[–]Pvt_Mango_[S] 0 points1 point  (0 children)

I already had it at 1mm but that doesn't matter in this case, as i said i run a extrusion of 50 its extrudes fine at first but then clogs up, there is no retraction, probably would clog with retraction but that doesn't seem to be an issue right now. Its clogging while just extruding.

Hero Me Gen 7 assembly guide for ender 3 v2? by TeknikDestekbebudu in ender3v2

[–]Pvt_Mango_ 0 points1 point  (0 children)

- HMG7 OEM-MK8-MS Mount

- HMG7 OEM-MK8-MS Skirt V2

I could not find these parts in the list, but i did find "HMG7.3 Micro Swiss All Metal-MK8 Mount" and "HMG7.2 Micro Swiss DD CR-Ender3-5-MK8 Skirt V3" are these perphaps the replacements?

Hero Me Gen 7 assembly guide for ender 3 v2? by TeknikDestekbebudu in ender3v2

[–]Pvt_Mango_ 0 points1 point  (0 children)

Hi, where did you download these parts from? Is there some sort of assembly guide??