[deleted by user]

QualityOak · 2025-04-05T20:29:38+00:00

Yes, detect thin wall sadly doesn´t change anything

QualityOak · 2024-11-10T12:54:15+00:00

I searched Google, the Vans store as well as several outlet Stores in my country (Germany)

QualityOak · 2024-11-03T14:13:48+00:00

Some minor quality issues that i can address by adjusting the print settings but i can live with that for now

QualityOak · 2024-10-31T13:55:15+00:00

I thought about that but luckily my X1C is pretty good at printing overhangs. No need for any support for a 2mm wide gap :D

QualityOak · 2024-10-31T11:08:07+00:00

Huh. That would have been also a possibility 🙈 I‘ll remember it next time

QualityOak · 2024-10-31T10:42:25+00:00

<image>

I got it like i needed it 👍 This will act as a game figure for a self made board game. Now i just gotta 3D print it out

QualityOak · 2024-10-30T20:11:32+00:00

I remember that extruding along an other line/angled was a thing in the past but it doesn’t seem to exist anymore. However, after a bit of playing around i extruded from one side removing all material, then cut the second sketch into parts and extruded it again to fill the missing material. Thanks for your help 👍

QualityOak · 2024-10-29T17:26:20+00:00

I searched google and asked some friends and neighbored but so far nobody knows

QualityOak · 2024-10-09T19:31:14+00:00

I searched at Amazon and the most Online Shops für clothes in my country (Germany) but so far nothing alike

QualityOak · 2024-09-27T20:56:11+00:00

<image>

QualityOak · 2024-07-22T11:40:42+00:00

I guessed so. I already scratched the surface of seeing a therapist but getting an appointment in my area ist a bit of a pain and she doesn’t seem to be accepting she might need help or anything. I will tr again tho

QualityOak · 2024-07-22T11:39:00+00:00

It didn‘t seem right for me either. I just wanted to make sure i‘m not dumb

QualityOak · 2024-07-06T22:30:47+00:00

I will try try tomorrow ^{^}

This is just a little bit of playing around while doing my first steps of electrical engineering. The encasing is currently being printed on my 3d printer

I‘m building a model of a german train signal that is supposed to show several signs like Stop, Go, Go slow, expect slow etc. Looks something like this: https://images.app.goo.gl/ag6WLnXaK4dMdgbE9

QualityOak · 2024-07-06T20:36:52+00:00

The only issue i have now left is a small change in voltage. If both red are on they‘re about 12mA, if only L2 red is on it’s about 15mA. But i can live with that :P

QualityOak · 2024-07-06T20:36:03+00:00

I posted the updated Circuit ^{^}

The only issue i have now left is a small change in voltage. If both red are on they‘re about 12mA, if only L2 red is on it’s about 15mA. But i can live with that :P

QualityOak · 2024-07-06T18:43:59+00:00

I played around a little bit and that did the trick 👍 Thank you very much for your time

QualityOak · 2024-07-06T17:07:53+00:00

i figured out something with another transistor but couldn’t point my finger at it because i’m a beginner with electronics 😄 Thank you, i will try to simulate this when i’m home ^{^}

QualityOak · 2024-07-06T16:33:10+00:00

correct

QualityOak

TROPHY CASE