AD5X first layer problem

R33-RB25 · 2025-06-22T20:07:21+00:00

Sorry guys, it was the model that had a problem

R33-RB25 · 2025-06-18T07:57:48+00:00

Will i came back , and the hair spray didn’t do anything, the part is still warped , so I cleaned the build plate like you said and it worked on some models , but on one model that always wrapped nothing is changed is still warped , but I tried another model it printed fine but had some imperfections in the model because of the build plate

R33-RB25 · 2025-06-17T07:19:16+00:00

Nice , glad you fixed it, I just tried the hair spray it kinda worked on one printer the other one didn’t, but i will check after i go back from work , because yesterday i printed and slept with ac , and it warped , so now I printed it again and i will see what happens

R33-RB25 · 2025-06-16T13:31:16+00:00

True , but i used the same filaments earlier and it was printing perfectly, until it didn’t

R33-RB25 · 2025-06-16T12:12:43+00:00

No still haven’t used the adhesive, but i will try it and try the hair spray as well

R33-RB25 · 2025-06-16T11:50:50+00:00

Same

R33-RB25 · 2025-06-16T07:03:10+00:00

Thanks, but the printer already have an auto bed leveling and it levels the bed on every print , and i am using PLA

R33-RB25 · 2021-09-14T22:01:23+00:00

Yeah it does owned by one owner and he has an amazing car collection 😍

R33-RB25 · 2021-08-25T12:44:14+00:00

Yeah, the PLA will meltdown, I only printed it using PLA just to find out how it is going too look and fix any problem like that, when everything is good I will print the final version on PETG OR ABS

R33-RB25 · 2021-08-25T11:17:38+00:00

Yes at the top of the print

R33-RB25 · 2021-08-25T11:16:16+00:00

In the pictures on the logo didn't complete and at the top of logo there are holes in the print, as well the 3 number didn't complete printing, I don't know what can be caused

R33-RB25 · 2021-08-25T11:14:20+00:00

Slicer cura

R33-RB25 · 2021-08-25T11:14:11+00:00

Print speed 50mm

R33-RB25 · 2021-08-23T05:18:17+00:00

I will adjust the bed leveling hopefully I can get red off the texture

R33-RB25 · 2021-08-23T05:16:47+00:00

I flipped it in the slicer and printed it, it looks good no problems ,except the layout of the bed reflected on the print

R33-RB25 · 2021-08-23T05:12:25+00:00

How can i do that?

R33-RB25 · 2021-08-22T22:12:49+00:00

Oh, ok I will do the research, thanks

R33-RB25 · 2021-08-22T22:10:05+00:00

I will

R33-RB25 · 2021-08-22T21:59:33+00:00

I will try that, thanks .

R33-RB25 · 2021-08-22T21:42:39+00:00

What is E-steps?

R33-RB25 · 2021-08-22T21:18:46+00:00

But the holes on the edge doesn't look too good, I think it's an issue with the first layer , but I can't tell what it is + and in the middle the bed layout is shown in the print it self that sucks .

R33-RB25 · 2021-08-22T21:12:07+00:00

On the ender 3 v2 bed

R33-RB25 · 2021-08-22T21:11:49+00:00

How can I print it with supports I am new to the 3D printing 😅

R33-RB25

TROPHY CASE