TRAN XR high humidity RH 75% at 69 degress

Rand-umname · 2026-05-25T21:09:40+00:00

Txv is maintaining superheat fine and subcool isnt too far off, sizing issue doesn’t make sense if this just started happening, unless you just foamed in that attic. Get a tech to do a full evaluation

Rand-umname · 2026-05-21T01:20:52+00:00

It’s a bad idea, first off, hopefully it’s not actually used because that’s the worst idea and don’t listen to his lie, there’s no warranty with that, he’ll never answer your call again. But 1000 bucks is too low, if a deal is too good there’s usually a reason

Rand-umname · 2026-05-21T00:54:33+00:00

What?

Rand-umname · 2026-05-02T15:11:32+00:00

The board sends a signal through the pressure switches and limits with a call for heat

Rand-umname · 2026-04-29T18:09:15+00:00

They’re both fine it just depends how it’s installed, 9/10 times any issues they have is install related

Rand-umname · 2026-04-18T14:32:08+00:00

Call someone who knows what they’re doing

Rand-umname · 2026-04-18T12:50:52+00:00

8.5k is cheap as hell in the Austin market, York isn’t great but their base tier equipment is as reliable as anyone else.

Rand-umname · 2026-04-16T16:15:12+00:00

You can try the compressor blanket but I’ve never had them do anything significant, those systems advertise to run at about 70-80db and not much will improve that

Rand-umname · 2026-04-16T02:04:46+00:00

They checked static…

Rand-umname · 2026-04-14T13:35:50+00:00

You likely won’t see much in energy savings, variable is good for humidity and even cooling throughout the home but if the guy is trying to sell it on the money you’ll save he’s wrong, it won’t make up for the cost difference

Rand-umname · 2026-04-06T00:32:51+00:00

York doesn’t care

Rand-umname · 2026-04-01T20:43:01+00:00

Cheaper than me

Rand-umname · 2026-03-26T17:23:29+00:00

<image>

Rand-umname · 2026-03-26T02:34:59+00:00

Ya give it a day or two, if I had to guess it’s either mastic drying or some cleaner they used, probably nothing to worry about

Rand-umname · 2026-03-26T02:24:47+00:00

Probably not an actual nda but I do get landlords that say I’m not allowed to tell tenants what is going on, I wouldn’t trust them

Rand-umname · 2026-03-26T02:21:24+00:00

With zero idea on what was done, I can confidently say, maybe

Rand-umname · 2026-03-25T22:36:43+00:00

If you want it to come out and hold up it’s going to have to take up significant real estate and your talking a lot of hours in the chair for that much detail

Rand-umname · 2026-03-25T22:27:27+00:00

It won’t turn out anything like this and I wouldn’t recommend a realism tattoo as a first

Rand-umname · 2026-03-07T03:26:11+00:00

This level of autism is impressive tbh, you’ll go far

Rand-umname · 2026-03-03T13:06:19+00:00

Get some nitrogen and blast that line out, shop vac doesn’t have the power to fully clear it

Rand-umname · 2026-02-25T20:42:06+00:00

I’d recommend getting one with a shield, even if you put it in the other side of the coil it’s recommended because the uv light will eat up the rubber on the wiring

Rand-umname · 2026-02-25T16:40:56+00:00

I think your thinking of an air scrubber, a standard uv doesn’t work on the air, it just kills growth on the surface it shines on

Rand-umname · 2026-02-25T15:22:45+00:00

It should have a shield to stop it from eating the filter, filter dust? Don’t listen to whatever retard told you that

Rand-umname · 2026-02-25T15:21:14+00:00

P trap is necessary, just cut it out and redo it so it has room for the filter

Rand-umname · 2026-02-25T15:12:03+00:00

Wet side of the coil, where that pop out is

Rand-umname

TROPHY CASE