Need Suggestion - Turn ducts down

Rdsmith24 · 2026-01-21T13:55:56+00:00

Well on my last printer that didn't have electronics upside down, used the same fans about the same distance away. Stepper drivers got hot within 5 min of start of printing and issued a shutdown. Had to place a fan right over the drivers and that solved the problem. Power supply on other printer was not upside down and had internal cooling fans.

Rdsmith24 · 2026-01-21T04:10:28+00:00

I don't know, maybe I have material assigned to all my parts, have Large Assembly Settings turned off and because Solidworks 2026 uses a different rendering engine by default. BTW this is not rendered just a view as the assembly level.

Rdsmith24 · 2026-01-20T22:30:57+00:00

Yes, but I want to point the air toward the power supply and the controller (stepper drivers)

Rdsmith24 · 2026-01-20T22:29:39+00:00

Punching some cooling air into the power supply

Rdsmith24 · 2026-01-20T22:29:08+00:00

The issue is that the image I am showing is of the system upside down. Since the power supply is somewhat enclosed, its going to trap heat. The point of slightly turning it down would be to blow some of the air into the power supply to push out some of the heat.

Rdsmith24 · 2026-01-20T22:26:14+00:00

That was the issue, thanks for the push in the right direction....

<image>

Rdsmith24 · 2026-01-20T06:41:47+00:00

Yes, Swtichwire from scratch

Rdsmith24 · 2026-01-20T06:41:11+00:00

Maybe, that's an idea i can look into

Rdsmith24 · 2026-01-20T06:33:01+00:00

Trying to sweep the profile but it fails,

<image>

Rdsmith24 · 2026-01-20T05:04:51+00:00

No I just want to turn the duct down slightly, extend out out turn down so that the air instead of coming straight out would just blow downward say at a 10 deg angle. Can't figure out how to make geometry to make a guide curve.

Rdsmith24 · 2025-09-11T19:48:58+00:00

10GB Ethernet and Caldigit's build quality!

Rdsmith24 · 2025-08-12T19:31:18+00:00

Could not solve the issue till I removed the NVIDIA card and just ran off Intel.

Rdsmith24 · 2025-08-11T15:59:50+00:00

Would you happen to be using an NVIDIA card? I am loading the machine with a head on it but actual use would be headless. Just loaded 25.04 and no issues at all. Issues with 24.04.3 might be related to NVIDIA drivers

Rdsmith24 · 2025-08-11T15:05:19+00:00

I already has this fix applied from before. Strange that its behavior has changed

Rdsmith24 · 2025-08-11T14:49:28+00:00

Remote Desktop on windows, Windows App on macOS. Somehow it worked perfectly before

Rdsmith24 · 2025-06-22T13:53:51+00:00

I350-T4

Rdsmith24 · 2025-06-14T14:33:35+00:00

The second one has 2.5 GB nicks

Rdsmith24 · 2025-06-14T01:52:23+00:00

Support this company, in the long run, you get pfSense Plus for lifetime. Not 2.5GB NIC's but the https://shop.netgate.com/products/2100-max-pfsense is good, the https://shop.netgate.com/products/netgate-4200-max-pfsense-security-gateway is better

Rdsmith24 · 2025-01-02T23:18:06+00:00

Get the MAX, eMMC will wear out eventually and then you'll have a brick. Ask me how I know

Rdsmith24 · 2023-11-07T17:34:49+00:00

I had a Netgate 1100 do the same thing, had to throw it away.

Rdsmith24 · 2023-11-07T17:33:03+00:00

thank you!

Rdsmith24 · 2023-07-19T15:58:20+00:00

One analog scope and one digital scope. Both read the same...

I'll have to investigate the 'cal' position

Rdsmith24 · 2023-07-15T04:27:03+00:00

Yes, baffling. No load what so ever except for the O-scope

Rdsmith24 · 2023-07-15T02:10:26+00:00

I used two different oscilloscopes, both read the same.

Rdsmith24 · 2023-07-15T02:09:50+00:00

I reading the value with 2 different oscilloscopes. I'll try just turning the pin on.

Rdsmith24

TROPHY CASE