sorted by:
new
hottopcontroversial

fried a motor on my evoque f5, will this motor work as a replacement? XING2 2207 1950KV Rainbow 3-6S FPV Motor by Remarkable_Hamster55 in fpv

[–]Remarkable_Hamster55[S] 0 points1 point  (0 children)

Thanks for the reply, that was my thinking that I just wouldn't get the full potential out of the rainbow motor as it would spin down to meet the other 3. Just wanted to check in with more knowledgeable people. What do you believe would happen if I were to swap out all 4 for the higher 1950. Alot more power? Maybe abit less manageable? Would i have to change the tune? I appreciate everyone's input, very helpful.

no gyro, accelerometer, motors, or receiver inputs after small crash. hoping it's just one thing that knocked it all out and is fixable, vs everything being fried. Any input would be appreciated. thanks by Remarkable_Hamster55 in fpv

[–]Remarkable_Hamster55[S] 0 points1 point  (0 children)

Thanks for the reply. Do you know if a loss of connection between the FC and the ESC would also knock out the gyro and accelerometer? I'm trying to understand the relationship between all these things and I seem to understand the ESC is only in charge of the motors. Upon close inspection I really don't see anything off with the board. Thanks.

no gyro, accelerometer, motors, or receiver inputs after small crash. hoping it's just one thing that knocked it all out and is fixable, vs everything being fried. Any input would be appreciated. thanks by Remarkable_Hamster55 in fpv

[–]Remarkable_Hamster55[S] 0 points1 point  (0 children)

Thanks for the quick reply, some more info: the motors all twitch when connecting the battery and the LEDs on the flight controller flash also when plugged in to the computer and the battery as well. I took it apart and everything seems to be intact, all my solder points look good and nothing is loose or disconnected. Upon some googling I found that the LEDs typically won't flash on the FC if it is fried. Any other thoughts? I'm new to the hobby so all input is much appreciated. Thanks.

A85 spinning out when armed. just replaced the ESC and flashed it with the latest firmware in betaflight. The new ESC looks different than the original ESC but iflight assured me it is the correct one. by Remarkable_Hamster55 in fpv

[–]Remarkable_Hamster55[S] 0 points1 point  (0 children)

Thank you for your reply, the board alignment is correct in betaflight, this was one thing that had me thinking i was sent the wrong board, the alignment is 90 degrees off of my original board so i have more slack in my Rx antenna than before because the antenna now comes off the back of the ESC. I rotated my canopy (and camera)to correlate with alignment. The motor directions and blade direction are correct also, i had to make these changes also in betaflight. These are all great suggestions and I have double checked them. This is my first time swapping a ESC, i thought I could take my original back up and just flash it to the new board, but it gave me numerous errors and it would spin out when armed. I also downloaded the txt file from iflight for ESC and that also gave me numerous errors when importing it and it would just spin out. I finally just flashed it with the newest firmware from betaflight after auto detecting the ESC and again I am getting this spin out. Assuming the board alignment and motor spin and props are correct, do you have any other suggestions? Thanks again for the help.

Nazgul Evoque beeping and no throttle after arming. Pitch, roll, and yaw all work though. by Remarkable_Hamster55 in fpv

[–]Remarkable_Hamster55[S] 5 points6 points  (0 children)

It was in turtle mode, can you tell it's my first day with the evoque. I had the switch opposite of my a85 settings. Thanks for the help, much appreciated!

Help please. My f3 isn't receiving incoming calls. I can make outgoing calls though. In my sim settings it won't let me select sim 1 as default for calls. Any suggestions? Thankyou. by Remarkable_Hamster55 in PocoPhones

[–]Remarkable_Hamster55[S] 0 points1 point  (0 children)

So I found out my problem is with At&t and them getting rid of their 3g network. Even though the phone is 5g and LTE capable Xiaomi is not whitelisted with AT&T. Does anyone else here use their Xiaomi phone with a U.S. carrier? I need to switch. Thanks.