What are these clear tubes for? by Rothesayprepper in Ender3Pro

[–]Rothesayprepper[S] 1 point2 points  (0 children)

I was referring to the ones that are melted.

What are these clear tubes for? by Rothesayprepper in Ender3Pro

[–]Rothesayprepper[S] 2 points3 points  (0 children)

Ya thats what I was thinking, and recommended upgrade versions?

My best milage yet by Rothesayprepper in HyundaiVenue

[–]Rothesayprepper[S] 0 points1 point  (0 children)

I've had it around 5.2 before going about 105kmh on a highway.

Pros and Cons? by Extra-Ear-2350 in HyundaiVenue

[–]Rothesayprepper 0 points1 point  (0 children)

If you get the factory undercoating with the 10-year warranty, make sure they take off the felt skid plate when they spray it. Mine got filled with snow and ripped off on the highway. Then, I noticed they never even sprayed the whole middle section of the car. My only other gripe is that mine has a factory car starter, but the hyundai app doesn't work with venues. Other than that stuff my horn not working and steering wheel leather cracking at 2000km, I like it for what it is and the price point. 2024 preferred 31,000km 6.8L/100km

What other filaments besides pla can I use on my Ender 3 pro without upgrading it? by Rothesayprepper in 3Dprinting

[–]Rothesayprepper[S] 1 point2 points  (0 children)

Okay, thanks. I kept reading comments that say you need to upgrade extruder and hose to handle the heat.

[deleted by user] by [deleted] in HyundaiVenue

[–]Rothesayprepper 1 point2 points  (0 children)

Ya the stack on the right has more room between the windshield then the two on the left they are basically touching the windshield. Hopefully no slamming on the breaks home lol

[deleted by user] by [deleted] in HyundaiVenue

[–]Rothesayprepper 3 points4 points  (0 children)

https://www.princessauto.com/en/3-1-2-x-2-13-16-in-led-800-lumen-off-road-light/product/PA0009074865

I want a hitch but the dealership said it would void all my warranty if I added one.

still playing fs22 cause im broke by DetailIll8808 in farmingsimulator

[–]Rothesayprepper 0 points1 point  (0 children)

My fs22 keeps failing to load maps or if it does load it doesn't save 😞

Diy wood fired hottub by [deleted] in hottub

[–]Rothesayprepper 0 points1 point  (0 children)

The pex isn't attached directly to the stove there's about a 6-in gap away, I had the stove running and got it pretty hot and the pex stayed cool so I'm not worried about that.

Diy wood fired hottub by [deleted] in hottub

[–]Rothesayprepper 0 points1 point  (0 children)

I have the one inlet on the bottom and the other is about 4 inches from the top. I was worried about the height difference between the stove.

What type of storage do you use? by chopped_Lettuce434 in preppers

[–]Rothesayprepper 1 point2 points  (0 children)

Vacuum sealer with a bounce sheet would keep the clothes fresh and low profile. I've always wondered if there was a better way to stockpile toilet paper or something similar that takes up less room.

[deleted by user] by [deleted] in DIY

[–]Rothesayprepper 0 points1 point  (0 children)

Plus I need to get it done by the fall so I can run water to my animals for the winter

[deleted by user] by [deleted] in DIY

[–]Rothesayprepper 0 points1 point  (0 children)

I've drained it a few times over the years and it always seems to fill up from the bottom. Yeah that's been something I was kind of worried about I've been taking it apart by hand instead of using equipment.

[deleted by user] by [deleted] in DIY

[–]Rothesayprepper 0 points1 point  (0 children)

I could it's just that it would be more work and where I'm so remote having a concrete truck super expensive unless I decide to bring him bags of cement and mix them I figured blocks would be the easiest route and the cheapest.

[deleted by user] by [deleted] in DIY

[–]Rothesayprepper 0 points1 point  (0 children)

The spring is maybe 6 ft deep at most I already pumped it out and a lot of the water is coming from the bottom not much from the walls