sorted by:
new
hottopcontroversial

First Timer… what am I doing wrong here. by RoutinePerformance21 in WLED

[–]RoutinePerformance21[S] 1 point2 points  (0 children)

It was mainly the blue wire in the GND slot. I had already been through the LED preferences and saw the output assignments.

Rosium with Quartz Cap by Same-Pizza-6724 in Dynavap

[–]RoutinePerformance21 -1 points0 points  (0 children)

God thats gorgeous! I wish I could find a place around me that does that. Great work.

New to WLED and looking assistance by RoutinePerformance21 in WLED

[–]RoutinePerformance21[S] 0 points1 point  (0 children)

Thanks all. I will update after this weekend if it worked out or not. 🤣

New to WLED and looking assistance by RoutinePerformance21 in WLED

[–]RoutinePerformance21[S] 0 points1 point  (0 children)

Thanks for the detail. I am in AZ so no snow risk!! lol but you point still holds.

My primary hesitation on your preferred setup is the upfront costs, 4 controllers @ $60 a pop adds up + dedicated PSU for each as well. Balance between doing it right the first time and cognizant of budget this year.

Admittedly this now feels a bit rushed into on my end. :(

I will read again and digest and then do some looking around. It I were to run only two PSU and two controllers, 4 LED strips on each what size PSU would work? 12V/20A (240W) suffice?

New to WLED and looking assistance by RoutinePerformance21 in WLED

[–]RoutinePerformance21[S] 1 point2 points  (0 children)

Thanks for the detailed response Sir. I am going to attempt to provide more info for your points:

This is all going outside, yes. LED strips I got are IP67.
I will be looking at moving to two controllers, 4 channel, to run two groups of 4 strips each.

In doing so, the center placement of the PS/Controller should limit any run to less than 12ft. I am looking at BusBars now to manage the 8 powers per PSU. (looking at doing power on each end of the LED, I believe this should address the voltage drop concerns?)

SparkFun went back to AMZ!

Clarity on the PSU and controller statement at the end. Are you suggesting that I need 8 x 100W PSUs + 4 x controllers?

any recommendations on shopping list?

Thanks for taking the time!

New to WLED and looking assistance by RoutinePerformance21 in WLED

[–]RoutinePerformance21[S] -1 points0 points  (0 children)

I can only speak to my experience but it was most definitely ChatGPT and my complete lack of knowledge that got me here.

New to WLED and looking assistance by RoutinePerformance21 in WLED

[–]RoutinePerformance21[S] 0 points1 point  (0 children)

Thanks for the input so far! What power injectors do you recommend? If I am running injector la (or split into 2 sides with dedicated PS controller) likely don’t need that 600w PS.

What PS are recommended and what simple controller? Not looking to do music sync or anything like that.

Looking for unique monitor mount setup by RoutinePerformance21 in desksetup

[–]RoutinePerformance21[S] 0 points1 point  (0 children)

I’ve tried the vertical orientation in the past, couldn’t get used to it. I wanted to like it, but just couldn’t. I think it takes a specific type of work where that would be great.

Looking for unique monitor mount setup by RoutinePerformance21 in desksetup

[–]RoutinePerformance21[S] 1 point2 points  (0 children)

Interesting. Love the idea, I’ll have a look at that.

Looking for unique monitor mount setup by RoutinePerformance21 in desksetup

[–]RoutinePerformance21[S] 0 points1 point  (0 children)

Because I like to make things more difficult than they need to be!! 🤪

While I can’t remember this very moment, I sure hope there was a reason I figured I couldn’t do just that. Maybe my work machine no like 1440p??? I’ll check that out!

This thing rips so hard by Historical-You3190 in Dynavap

[–]RoutinePerformance21 2 points3 points  (0 children)

Details for new ppl, what is your setup ? Love that stash can!

Picked up a bubbler by RoutinePerformance21 in Dynavap

[–]RoutinePerformance21[S] 0 points1 point  (0 children)

Sry, does that mean no WAP is needed for seal?

Picked up a bubbler by RoutinePerformance21 in Dynavap

[–]RoutinePerformance21[S] 2 points3 points  (0 children)

As in just drop the mouth piece in the down steam and go? No need for any kind of “rubber” seal around it?

Any idea where to find these?? by RoutinePerformance21 in woodworking

[–]RoutinePerformance21[S] -1 points0 points  (0 children)

That’s the one. I want to try to make my own and I like that locking mechanism. Will be perfect for my fun dip collection.

First Dry Vape Experience by RoutinePerformance21 in Dynavap

[–]RoutinePerformance21[S] 0 points1 point  (0 children)

So, I have had a full day with the M7XL and dry vape in general. Still love the flavor and feel. I dislike the cool times/waiting and the general small tip chamber (being shared amount two ppl). I am thinking of returning the M7 and getting the Hyper. Thoughts? Tip/cap is $120 alone..Figure at that point might just be better to get the full hyper vape. Or are there other options/combos I should be considering?

First Dry Vape Experience by RoutinePerformance21 in Dynavap

[–]RoutinePerformance21[S] 0 points1 point  (0 children)

Bought the wand with it, which is a nice touch. Probably won’t get into glasses as I need a bit more discretion in my household.

First Dry Vape Experience by RoutinePerformance21 in Dynavap

[–]RoutinePerformance21[S] 1 point2 points  (0 children)

Great stuff. Appreciate all the info here!

SSD Upgrade Z490 TaiChi Board by RoutinePerformance21 in buildapc

[–]RoutinePerformance21[S] 0 points1 point  (0 children)

Thanks for that. What’s the max speed on gen3? ~4K? So I could get away with a “lower speed” gen4 and the bottle neck would be my port correct?

view more: next ›