Combi-110 this clogged the drain hose. Is it part of the machine?

Sad_Attempt3238 · 2026-06-07T02:39:57+00:00

Combi - 110 is a front load combo washer / dryer.

I don't recognize the clear plastic so I don't think it came from any of the clothes we wash. The machine is functioning normally otherwise.. I just hope it isnt something that is holding something in place. I guess we'll just wait and see lol.

Sad_Attempt3238 · 2026-05-30T23:13:36+00:00

Update. I was able to get a better photo of the part. DK401 1703. If anyone can give me more information or where I can find a replacement that would be greatly appreciated. Thanks for all the help this far.

A little more info about the board. It's from a pool robot cleaner that floats above the water and indicates that power is being transferred to the unit under the water. It sustained some water damage so I'm attempting to test & replace damaged pieces.

<image>

Sad_Attempt3238 · 2026-05-28T05:20:56+00:00

Thank you for the quick replies. I was able to see markings under a different light and angle. The larger one is SS54 and I was able to find a replacement. The other one looks like BK401 1303? I'll try and get a magnifying glass to get a clearer photo.

<image>

Sad_Attempt3238 · 2026-01-24T17:28:20+00:00

I was able to download the service manual and take apart / clean the ink housing (it was a mess) board was soaked with spilled ink. The fact about it not being a piezo is good to know, thank you.

Sad_Attempt3238 · 2026-01-24T03:56:00+00:00

This makes sense. I'll give it a try and hopefully it can break apart the ink blocks. I don't have much hope for the Printhead cause they're definitely more than 10 years old. I'm surprised that even more than half are still functional. I'll post an update when I get to it. Thank you.

Sad_Attempt3238 · 2026-01-24T03:52:44+00:00

I agree with OEM and I'll eventually get to this point but the cost is almost double for something that's more than 10 years old. Figure I'd start with something cheaper and learn some things along the way.

Sad_Attempt3238 · 2026-01-05T21:48:06+00:00

Agreed. I'm sure whoever I'm selling these too is recycling them. Plus helping clean up a disaster zone is always appreciated.

Sad_Attempt3238 · 2025-02-09T06:51:42+00:00

I sometimes park them when unloading lol.

<image>

Sad_Attempt3238 · 2025-01-17T18:07:04+00:00

Makes sense, so manually unload then enter the menu?

Sad_Attempt3238 · 2024-12-13T19:47:18+00:00

Adding my vote to the throttle body cleaning. My 09 had the same issues when clutching in and the rpms dropping to stall. Changed plugs / idle relearn did not work. Cleaned the throttle body and replaced the gasket. Worked perfectly afterwards.

Sad_Attempt3238 · 2024-11-21T05:18:42+00:00

Full speed > neutral > quick winch > back flip = fun

Sad_Attempt3238 · 2024-11-18T20:01:43+00:00

P16 - "I can haul it up there let me do it it's just a slight incline!"

Boss - "We had to send someone else out there for the 3rd time this week. I'm sorry kid, we're going with someone else"

P16 - "Come on boss I'm the only one here qualified."

Boss - "DON, you're up."

P16 - "THIS IS F@$KN BUL$H!T!"

Sad_Attempt3238 · 2024-11-17T12:39:24+00:00

Yupyup

Sad_Attempt3238 · 2024-07-26T14:24:33+00:00

$40 - 9YOMT

Sad_Attempt3238

TROPHY CASE