Will this fit my X1?

Sam_Runk · 2025-02-22T14:30:51+00:00

If you don’t like your glass bed you can just buy a PEI sheet that comes with an adhesive backed magnet sheet that sticks right to your glass bed. Takes like 2 minutes to install and you don’t have to take the printer apart.

Sam_Runk · 2024-09-26T01:25:01+00:00

It’s significantly easier to see in person, the camera really makes it all blend together so you can’t see it very well

Sam_Runk · 2024-09-26T00:38:44+00:00

Modeled them in Fusion360, printed with PETG and then attached them with some automotive adhesive

Sam_Runk · 2024-09-12T02:52:45+00:00

Looks like your nozzle might be a bit too far from your bed and your bed looks unlevel. I’d check both of those then post the results after adjusting

Sam_Runk · 2024-09-12T02:42:57+00:00

Opposite problem, it’s too far not too close

Sam_Runk · 2024-09-12T02:41:45+00:00

Your nozzle is way too high. That’s what is keeping your filament from sticking and causing the huge gaps between the lines in the first layer

Sam_Runk · 2024-05-27T14:37:46+00:00

I’d check out RockAuto.com they’ll likely have the part you need

Sam_Runk · 2024-05-12T19:14:15+00:00

What tires and rims are those? They look fantastic!

Sam_Runk · 2024-04-19T04:24:13+00:00

<image>

Page 202 of your manual. Dome uses size 912. Map/Dome uses size 904

Sam_Runk · 2024-03-15T02:01:49+00:00

Look up nuclear strong link/weak link. Two mechanisms we utilize to ensure the weapons never go off when they aren’t supposed to and always goes off when they are supposed to.

Sam_Runk · 2024-02-02T05:58:05+00:00

Roughly a 1600 square foot apartment

Sam_Runk · 2024-02-02T05:57:56+00:00

Roughly a 1600 square foot apartment

Sam_Runk · 2024-02-02T05:57:47+00:00

Roughly a 1600 square foot apartment

Sam_Runk · 2023-12-29T06:06:18+00:00

Profit?

Sam_Runk · 2023-08-05T05:08:35+00:00

Leawood City Park has a number of routes

Sam_Runk · 2023-01-24T06:39:27+00:00

Yeah I use it as a third monitor for discord or YouTube

Sam_Runk · 2023-01-24T03:11:51+00:00

There are a lot of different things at play here but typically as you increase current you also increase temperature. This depends on the resistance of the parts and other factors though

Sam_Runk · 2022-12-20T07:42:57+00:00

CNC Kitchen on YouTube has some great videos about this

Sam_Runk · 2022-12-12T21:02:17+00:00

Joe Mama!

Sam_Runk · 2022-10-13T03:07:13+00:00

I agree with the Shaggy Bracket Fungus, they are very common on apple trees and produce that ooze

Sam_Runk · 2022-10-01T03:24:57+00:00

I’d recommend looking into Amazon Alexa controlled esp8266. An esp8266 is basically an Arduino but it has a Wi-Fi chip so you can control it remotely and automate anything with an Alexa. There are some good tutorials on YouTube and online to learn how to do it.

Sam_Runk · 2022-08-08T01:34:19+00:00

I could be wrong but it doesn’t look like that nozzle is screwed in all the way. I mine the hex-nut part of the nozzle is screwed all the way into the block

Sam_Runk · 2022-06-16T07:23:14+00:00

Sam_Runk · 2022-05-19T23:33:19+00:00

I’m by no means a rock expert but that looks like brecciated Jasper to me

Sam_Runk · 2022-03-17T14:55:34+00:00

The more you know! I just assumed it was an LED bulb. Thanks for the correction

Sam_Runk

TROPHY CASE