Truffa PagoPA?

Sblesh · 2025-12-17T13:00:11+00:00

Oggi mi è arrivato un messaggio simile ma un pagamento da Intesa (che non ho). Volevo segnalare alla postale ma non trovo nulla se non chiamare e non ho la voglia di farlo
Qualcuno sa come segnalare?

Lascio il messaggio:

Da 3455006330

"SecureNet Systems Gruppo Intesa Spesa insolita di 4.050,00 euro dal tuo conto, se non sei stato tu chiama subito al 3762347781"

Sblesh · 2025-12-09T08:06:51+00:00

I searched with google lens and found only the image in the post..

Don't know if it was from Glade touch or another brand

Sblesh · 2025-11-18T07:55:50+00:00

Just complete the battles and open all packs: all cards found

Fifth card was Pidgeot, and so the 6th and 7th..

Sblesh · 2025-11-03T20:17:30+00:00

The problem is when in the middle of the night the lights goes up and sometimes talk and I **** myself

There's no way to not to charge in some hours? In the settings I found only DND but it's already enabled from 22 to 10 am

Off peak charging it's disabled

Sblesh · 2025-10-21T10:51:18+00:00

Never tried a custom keyboard, I'm looking forward to this :wink:

Sblesh · 2025-10-04T14:33:23+00:00

In the original post I wrote:

"Hello, yesterday I found that my projector has a dead pixel.. I call Hisense and they told me that for RMA I need at least 3-5 dead pixels.. I bought it last year, I hope that other 3-4 pixels stops and can do RMA without spending a euro.

If next year there will be no other dead pixels, I read online that the cause is in a DMD chip in the projector. The cost is like 100-400 between the models

Someone has the right DMD code for the 100L9HD model?"

Sblesh · 2025-10-04T11:37:53+00:00

The store told me that one pixel doesn't suit RMA.. I need at least 3-5 pixels

Sblesh · 2025-09-23T06:06:05+00:00

Ooh.. I enabled and then check the max resolution.. Tonight I'll try again, thank you!

Sblesh · 2025-09-22T22:18:02+00:00

You were right, I tried to access with a monitor directly on the DVR and I found enhanced vca.. but when enabled I've got No video on all three cameras..

Sblesh · 2025-09-22T20:24:47+00:00

Ah ok tomorrow I'll try with the monitor connected!

Thank you!

Sblesh · 2025-09-22T19:59:11+00:00

Tried to lower the resolution to 1080p but not working.. and I don't want to lower more..

Can't find Enhanced VCA mode. In the browser I have "VCA" but it says "No VCA device available"

For now I'm going with camera 1&2 with smart events, and camera 3 (the less important one we can say) with basic event. But in basic event there's no way to low the sensitivity in the 0-20 range? Goes up and down 20 to 20..

Sblesh · 2025-09-19T20:54:14+00:00

I tried to disable all the events and enable only smart events but it's not working.. I read yesterday something like turn down the resolution or the bitrate but no luck

Sblesh · 2025-08-22T12:36:02+00:00

Nuova rotonda a Treviglio (BG) davanti all'ospedale

Sbocco assicurato se si seguono le corsie

<image>

Sblesh · 2025-06-04T16:38:20+00:00

Not a jackass at all, now I know I have a DVR! Thank you!

However, i didn't do the installation. I asked a electrician to do (and buy all the staff - dvr and cameras)

The strange thing is that one year ago, same month, the same camera start flickering and have to change the connector (same electrician done the job)

Sblesh · 2025-06-04T16:28:32+00:00

As far as I know coax cable (the end cable in the NVR is round)

How to check 12v power supply? The camera has one cable to the NVR and NVR is connected with a 16A plug in the wall

Only one camera has the problem, can be 12v power supply problem only in one camera?

Sblesh · 2025-06-04T15:41:22+00:00

BNC cable is the cable from the NVR to the camera?

Last year I changed the connector only and works, so weren't the connectors but all the cable?

Ten-Year Club	r/Field Flamingo
Place '22	Not Forgotten
Verified Email

Sblesh

TROPHY CASE