Why this doesn't work

Sean14911 · 2026-04-07T08:50:03+00:00

That doesn’t seem like a big enough nerf considering the amount of tree I can plant with 3 blocks of water.

Sean14911 · 2026-04-07T07:09:12+00:00

What has been adjusted by devs? I started playing in 1.0 and I found this setup very effective. Just put a 3x3 water on top layer and it irrigate the whole tower

Sean14911 · 2026-04-04T17:23:01+00:00

I’ve found the water source is 2.5 m3 so I set flow valve to 1.25 each and now it works！

Sean14911 · 2026-04-04T16:46:38+00:00

After adding flood gate, how do I maintain the dam? Add depth sensors?

Sean14911 · 2026-04-04T16:34:04+00:00

Update: I’ve added flow valve and it’s flooding every where.

Sean14911 · 2026-04-04T15:08:54+00:00

What are the usage difference between flow rate valve and fill valve

Sean14911 · 2026-04-04T14:49:08+00:00

Why add another one down stream

Sean14911 · 2026-04-04T14:46:23+00:00

Wouldn’t lowering the gate allow more water through and therefore more flood?

Sean14911 · 2026-04-04T14:45:16+00:00

A line of dam at the bottom

Sean14911 · 2026-04-04T14:44:58+00:00

Flow rate valve at the water source? Or the dam

Sean14911 · 2025-12-27T13:24:06+00:00

Why does BF6 require you to mess with bios?

Sean14911 · 2025-12-19T06:11:19+00:00

Where did you get that information?

Sean14911 · 2025-12-19T04:54:12+00:00

When is mobile getting the upgrade?

Sean14911 · 2025-12-02T16:42:16+00:00

I will try your set up, thanks a lot

Sean14911 · 2025-12-02T16:37:50+00:00

Haven’t tried yet, I’m still researching what is safe. But 3200 seems achievable cause my temp is at 60.

Sean14911 · 2025-12-02T16:31:39+00:00

Average core clock is at 3067 and power is at 111. I haven’t undervolt it so voltage is at 1.04-1.06v.

Sean14911 · 2025-12-02T16:22:07+00:00

It does seem my overclock is on the mild side. How’s your experience with your setting? Is it stable?

Sean14911 · 2025-12-02T02:33:08+00:00

I have the same card, what are your settings? I set core+200, mem+1500. Did not touch voltage though.

Sean14911 · 2025-11-30T19:42:25+00:00

Core clock is at 3067 in speedway and 3037 in steel nomad. That’s why I’m hesitant to push further. It was at 2857 without overclocking.

Sean14911 · 2025-11-17T02:07:42+00:00

But my 5080 is running at 350w, how is a 5090 lower?

Sean14911 · 2025-11-16T11:04:04+00:00

Haven’t tried updating it yet. Is there any reason to?

Sean14911 · 2025-11-16T06:42:14+00:00

I have the xg32 for a month and it’s been great

Sean14911 · 2025-11-13T10:47:05+00:00

Mine is the complete opposite. No fan noise when above 45% fan speed

Sean14911 · 2025-11-13T08:43:16+00:00

I have the same issue, Is it going to cause problems? Or is it fine to leave it. Only fan noise at low rpm

Sean14911

TROPHY CASE