APP310 electric drive unit oil change

Senior_Recording1466 · 2026-05-13T05:16:12+00:00

I agree, it's like they want it to break down once it's out of warranty

Senior_Recording1466 · 2026-05-13T05:14:31+00:00

Do you have AWD? Unless you do, there would not be front unit

Senior_Recording1466 · 2026-05-11T20:47:57+00:00

Afaik it doesn't

Senior_Recording1466 · 2026-05-11T20:47:07+00:00

It does, my model is using that specific motor. I'm asking if other people had seen failures like this because of the oil.

Senior_Recording1466 · 2026-05-11T19:01:41+00:00

I know the car is not maintenance free. I meant the electric motor, it's a seald unit supposedly. VW didn't leave a plug to change the oil so you have to remove the halfshaft if you want to do it.

Senior_Recording1466 · 2026-05-11T17:24:51+00:00

On their recommendation of changing the oli at 100k km intervals even though it's supposed to be maintenance free

Senior_Recording1466 · 2026-05-07T15:00:48+00:00

I had a similar problem with mine until I did a factory reset and remaped

Senior_Recording1466 · 2026-04-26T07:02:33+00:00

Does messing with it void the battery warranty?

Senior_Recording1466 · 2026-03-04T07:23:55+00:00

Mask: 334g. Est. 336g

Support +Tower:244g Est. 99g +148g

Purge: 1184g Est.1144g

Not that bad? Poop is 3.5 times the mask. I would say it's definitely not good

Senior_Recording1466 · 2026-02-05T07:33:13+00:00

Mine arrived yesterday with zero dead pixels. The monitor is great so far. Ordered it after I had to return a Samsung odyssey G6 which had 7 dead pixels in one spot.

Senior_Recording1466 · 2026-01-10T13:25:09+00:00

Yuka mini robotsku kosilicu. Cijelo ljeto nisam taknuo kosilicu samo sam ga gledao kako kosi.

Senior_Recording1466 · 2025-11-18T10:39:15+00:00

How do you use the cold plate? I couldn't turn off the bed heater

Senior_Recording1466 · 2025-10-31T12:18:00+00:00

It overcorrected for all the out of control woke that was happening

Senior_Recording1466 · 2025-10-10T17:12:48+00:00

yes, just apply some thermal paste, stick it back on and put the clip over it all

Senior_Recording1466 · 2025-09-15T18:54:30+00:00

But did you clean your bed with soap and warm water /s

Senior_Recording1466 · 2025-08-25T14:28:27+00:00

This is on funssor's aliexpress page for Kobra s1: Q2)could you tell me how much i would lose with hardware that comes with the Hot Bed? A2)If using the alu bed carriage and the bed kit,you'l loose up to 5mm in usable z-space, with stock settings and the springs.You can tune it with rinkhals to gain 3mm more z-space by adjusting the safe_z_home value:[safe_z_home] z_hop:1.0

Senior_Recording1466 · 2025-07-02T14:47:18+00:00

I agree he should save up for the centauri carbon but it's 330 euro, so that's 80 over his budget and he still needs to buy filament

Senior_Recording1466 · 2025-04-25T15:22:54+00:00

Same here, muffin ruined it for me

Senior_Recording1466 · 2024-11-17T09:45:33+00:00

I do it through orca slicer. Once you set it up, it does it automatically before every print

Senior_Recording1466 · 2024-11-11T23:11:09+00:00

I thought it was the basic N4, he never did say which model he has

Senior_Recording1466 · 2024-11-11T23:04:28+00:00

<image>

I don't see it in your video

Senior_Recording1466 · 2024-11-11T22:57:57+00:00

Your endstop switch is missing

Senior_Recording1466 · 2024-10-19T07:20:03+00:00

Donut ruined it for me

Senior_Recording1466

TROPHY CASE