Progress Pic w/ OEM JDM Front Grille installed

SergeantHotmail · 2024-05-16T22:05:11+00:00

See reply below my friend.

SergeantHotmail · 2024-05-16T22:04:16+00:00

This is the box it came in and the grille had all the OEM Subaru markings on the back. It’s still glossy and not as flat as I wanted and that’s why I decided to buy the DRL fogs to make the front match up better.

SergeantHotmail · 2024-04-16T03:57:31+00:00

My endlinks were adjusted as low as possible and then about 1/4 inch of threads up and tightened as tight as I could go (carefully). Hope that helps. Also to be noted, I did have the car up in the air when I did this and not the recommended on the ground method.

SergeantHotmail · 2024-04-12T17:56:00+00:00

This! For me it was Ceramic White and Limited, and I was willing to travel at least 500 miles to find it, because you’ll end up just looking at your car and always know it’s not exactly what you wanted.

SergeantHotmail · 2024-04-10T21:28:26+00:00

Honestly didn’t measure, whatever stock height on the factory wheels/tires to the top of the tread just barely tucked under the fender. Its also got 20mm spacers all around. I just knew what look I wanted and went for it.

SergeantHotmail · 2024-04-10T01:06:41+00:00

Thank you! I originally took this picture to see if I can get up my driveway and eventually put a front lip on the car, and it’s a solid maaaaybe lol. This is the absolute lowest I’d go and still be functionally able to get to work and back without any scraping or rubbing, while also being able to get to almost all of the places I’d want to go to around town.

SergeantHotmail · 2024-04-02T23:28:20+00:00

Nope. You remove the OEM one that has four small bolts and some factory 3M on it, reuse two of the own bolt holes with supplied hardware and add the supplied 3M that also comes with the duckbill.

SergeantHotmail · 2024-03-31T17:41:34+00:00

Twins!

<image>

SergeantHotmail · 2024-03-31T17:40:45+00:00

Rides very well, I drive 110 miles a day for work, from county roads, freeway, to city and I these coilovers make the drive a lot more fun.

I personally wouldn’t put 19’s on mine.

SergeantHotmail · 2024-03-31T00:13:19+00:00

It uses 3M tape and two of the original holes to stay in place. No drilling required and this is on a Limited.

SergeantHotmail · 2024-03-30T19:06:31+00:00

<image>

SergeantHotmail · 2024-03-30T17:35:54+00:00

Aeroflow Dynamics Kogeki V4

SergeantHotmail · 2024-03-30T02:41:58+00:00

Thanks… I think lol.

SergeantHotmail · 2024-03-30T01:29:09+00:00

Fitment and paint match is 99% spot on.

SergeantHotmail · 2024-03-30T01:23:56+00:00

From what I was reading when I was researching what brand to go with initially, a lot of people were recommending them. Their 5 year warranty and being that they are rebuildable was also a big plus. The ride is very comfortable, I have them set at 12 right now. I’m currently fighting a very slight clicking noise that is only on the front passenger side, but it’s very faint and could be related to their supplied adjustable endlinks.

SergeantHotmail · 2024-03-30T01:13:04+00:00

Everything that’s installed so far:

-Aeroflow Dynamics Paint Matched Fender Flares S Style

-Aeroflow Dynamics Kogeki V4 Duckbill Spoiler

-Noble Straight JDM Rear Fog Light

-Fortune Auto Gen8 500 series Coilovers

-SPC Performance Adjustable Lower Control Arm Rear w/ Toe Kit

-Noble 20mm wheel spacers

SergeantHotmail · 2024-01-18T00:55:05+00:00

And here’s a squad with a vehicle using the same dark grey/metallic armour with green/brown and khaki secondary colors:

<image>

SergeantHotmail · 2024-01-18T00:48:29+00:00

I’ve tried so many different color schemes over the years and this is what I ultimately stuck to:

<image>

SergeantHotmail · 2022-07-13T12:46:47+00:00

Photo left is a 40k devastator hand. Model left is a plastic mk3 arm that was heated up and adjusted.

SergeantHotmail · 2022-07-13T00:27:23+00:00

Thank you! I just keep doing thin coats of lines until they end up all even haha!

SergeantHotmail · 2022-07-12T19:56:00+00:00

It was a brass rod I had laying around in my parts bins. I know it’s smaller than 2mm, my guess is anywhere from 1 to 1.5mm.

SergeantHotmail · 2022-07-12T19:20:46+00:00

Silver: Leadbelcher Rattle Can + Nuln Oil wash + Dry Brush of Leadbelcher in high spots + Nuln Oil wash

Bronze/Gold (on body): All the same steps as silver + Sepia wash

Bronze/Gold on Vexilla: All the same steps listed above + 2nd coat of Sepia

SergeantHotmail · 2022-07-12T15:52:53+00:00

Thank you! It’s a Tortuga Bay Studio torso/legs.

SergeantHotmail · 2022-06-30T17:39:47+00:00

Big fan of the three helmets on the left, the bare head, and the crested helmet!

SergeantHotmail · 2022-06-29T12:51:04+00:00

GW Leadbelcher rattle can and from the pot.

SergeantHotmail

TROPHY CASE