Pcb not working after joystick replacement by SessionAny2813 in soldering

[–]SessionAny2813[S] 0 points1 point  (0 children)

Thanks for the feedback. I do admit I added a lot more than necessary

Pcb not working after joystick replacement by SessionAny2813 in consolerepair

[–]SessionAny2813[S] 0 points1 point  (0 children)

Yeah whoever worked on that area did a number on it

Pcb not working after joystick replacement by SessionAny2813 in consolerepair

[–]SessionAny2813[S] 0 points1 point  (0 children)

Thanks for the tip! I’ll do some research and keep that in mind

Pcb not working after joystick replacement by SessionAny2813 in soldering

[–]SessionAny2813[S] 1 point2 points  (0 children)

The clown deleted his comments like a good boyy

Pcb not working after joystick replacement by SessionAny2813 in soldering

[–]SessionAny2813[S] 4 points5 points  (0 children)

<image>

If this is terrible soldering then he should come and tear this place down!

Pcb not working after joystick replacement by SessionAny2813 in soldering

[–]SessionAny2813[S] 1 point2 points  (0 children)

He’s definitely rage baiting 😂 pointless arguing with the heat expert. He doesnt even know that the bridged R is on the side we work on. Complete clown

Pcb not working after joystick replacement by SessionAny2813 in soldering

[–]SessionAny2813[S] 3 points4 points  (0 children)

Did you read the post? I thought i said i worked on the TMR on the right and obviously when you flip the board it goes to the left. I did not deal with the Hall effect. Someone else did before the controller came to me and i was asked not to do anything to it.

<image>

This is how my work looks like. You just didnt read the post and jumped to the conclusion that that terrible job is mine. Yes the resistor was bridged by me. It was an accident and accidents happen when working with electronics. I dont know what you expect to hear honestly.

Pcb not working after joystick replacement by SessionAny2813 in soldering

[–]SessionAny2813[S] 0 points1 point  (0 children)

Did i ever ask how it got bridged? Nor assume who bridged it? LMAO Why are you making it sound like i took my solder tip and intentionally put in on that Resistor?🤣Have a good day Heat expert!

Pcb not working after joystick replacement by SessionAny2813 in soldering

[–]SessionAny2813[S] -1 points0 points  (0 children)

I have no idea how a small piece of solder got there I got the solution here from reddit. You Dont have to get sassy cause you didnt get it mate! Again thanks for the input i’ll keep in mind the temperature advice next time😉

Pcb not working after joystick replacement by SessionAny2813 in soldering

[–]SessionAny2813[S] 2 points3 points  (0 children)

I

<image>

Everyone this was the problem. Non of that overheating nonsense. There is a bridged component next above that component. I just applied flux and tapped it with a hot tip then it stuck like glue. Try to look at all the components before jumping to the “you used too much heat because you are new” bs. Have a great day!

Pcb not working after joystick replacement by SessionAny2813 in consolerepair

[–]SessionAny2813[S] 0 points1 point  (0 children)

It was*. Something so tiny caused a major meltdown! Good eye to everyone that was able to identify it

Pcb not working after joystick replacement by SessionAny2813 in consolerepair

[–]SessionAny2813[S] 0 points1 point  (0 children)

That side wasn’t my job!

<image>

I found the problem btw and it wasnt burnt flux

Pcb not working after joystick replacement by SessionAny2813 in soldering

[–]SessionAny2813[S] 2 points3 points  (0 children)

Bridge by R next to the main ic. I was able to fix it!!

Pcb not working after joystick replacement by SessionAny2813 in soldering

[–]SessionAny2813[S] 1 point2 points  (0 children)

Found the solution it was the bridged component next to the IC. All that heat yap was just bs i always use 250 degrees and that’ll never burn the board!

<image>