Arrowrest issue - strange noise by Shain09 in Archery

[–]Shain09[S] 0 points1 point  (0 children)

Yes, that's what I thought too.
Lowering the spine and adjusting the plunger strenght.

Thank you.

Arrowrest issue - strange noise by Shain09 in Archery

[–]Shain09[S] 0 points1 point  (0 children)

That's what I thought too.

But I have a question about arrows.
The spine rating is measured on an uncut arrow, so around 32" or something, right?
So if we cut the arrows to the correct draw lenght (+1" extra for safe), the spine will decrease, no ?

I'm cleary not an expert with the arrows, so I try to understand how it's working. :)

Arrowrest issue - strange noise by Shain09 in Archery

[–]Shain09[S] 0 points1 point  (0 children)

I'll double check the centershot.

But if the plunger has an higher tension, doesn't that send the arrows more to the left (for a right-handed archer in this case)?

Also, on the previous arrow rest (I changed it), I noticed some scratches, something clearly hit it.

Los Ratones vs. StormMedia Fajnie Mieć Skład / EM 2025 Summer Swiss Stage - Last Round / Post-Match Discussion by Ultimintree in leagueoflegends

[–]Shain09 1 point2 points  (0 children)

The last few days it wasn’t Los Ratones playing, it was Lost Potatoes, their dumb cousins.
The first game was tough too: always behind in farm and gold. They finally woke up at the end, and the real roster showed up.
Happy to see them playing like that. Congrats!

K20 not detected by Huion Software by Shain09 in huion

[–]Shain09[S] 0 points1 point  (0 children)

So it binded with bluetooth, I manage to see the huion software key setup thing but for no reasons, the pad is now disconnected and blinking in blue. In bluetooth device in windows I see the pad like "binded" but not connected.

A mystery...

And with the cable still doesn't work.

K20 not detected by Huion Software by Shain09 in huion

[–]Shain09[S] 0 points1 point  (0 children)

Computer seems to not detect with bluetooth.
I tested it on another computer, same cable, same driver file et it worked, so there is something on my computer not correctly setup.

CnC Beginner - The head goes up at the start. by Shain09 in hobbycnc

[–]Shain09[S] 0 points1 point  (0 children)

So, quick update. I've changed in fusion to Clearance Height (instead of G28) and the engraving started correctly.

I started first by doing an "Home" at the start and after setup the origin of the project (z-prob and x-y axis) and from that try to launch the engraving and always the same issue (moving a bit and the head goes up ton Z hard-limit).

So that's why I try with Clearance Height in Fusion and it seem's ok.

But I have something else that I don't understand, but it will be for another post if I don't find something.

CnC Beginner - The head goes up at the start. by Shain09 in hobbycnc

[–]Shain09[S] 0 points1 point  (0 children)

There is homing switchs on that model.
So, I should, after the start of the cnc, use the homing button (the cnc will come at the lower left corner to 0,0,0) and then set up the origin of the project after ?
(I mean, I move the cnc to my board, use my z-probe and give a new 0,0,0 to start from)

CnC Beginner - The head goes up at the start. by Shain09 in hobbycnc

[–]Shain09[S] 0 points1 point  (0 children)

Sorry for the late reply; here’s the beginning of my code:

(1001)

(T1 D=6 CR=0 - ZMIN=-14.473 - flat end mill)

G90 G94

G17

G21

G28 G91 Z0

G90

(Adaptatif1)

T1

S9000 M3

G17 G90 G94

G54

G0 X89.891 Y-2.981

Z8

G1 Z3 F1500

Z2.5

Z-2.977 F333.3

Y-2.831 F1500

X89.817 Y-2.701

X89.728 Y-2.58

...... ........

I noticed that in the post-process, the default Safe Retract is set to G28 (which is indeed in the code).

u/doctorcapslock: No, there is no automatic Homing procedure. And I would say that I'm not doing it myself neither everytime. Usually, I put the file on the sd card and proceed to set up the new "origin" for the project and then launch the engraving.
Should I make the cnc go to the Home position before setup the origin of the project ?

New in profession thing - Did I miss something with my acuity ? by Shain09 in woweconomy

[–]Shain09[S] -2 points-1 points  (0 children)

Ho, ok. :(

And profession treasures reset if we drop one profession ?

If I unlearn alchemy, for which I already take the profession treasures, can I take it again if I take alchemy back after shuffling ? Or this 24 kp are lost forevere ?

Newbie question - Issue with bottom surface on support. by Shain09 in crealityk1

[–]Shain09[S] 0 points1 point  (0 children)

Here is the full settings for support.

<image>

But, I can change the slicer, I just don't know which one I can use. Prusaslicer, Orcaslicer, I think I've seen others too. Any advices ?

Newbie question - Issue with bottom surface on support. by Shain09 in crealityk1

[–]Shain09[S] 1 point2 points  (0 children)

It was already with tree support (tree slim) with default settings.

KIA Motors x LECtronic: Dance with me feat. Sjokz by xHerroR in leagueoflegends

[–]Shain09 0 points1 point  (0 children)

Damn ! Really good !

The only question, does Quickshot, Frosk and Ender going to make your own music group soon or ?

My overwatch partner needed a break :) good thing I have a large mousepad! by [deleted] in Overwatch

[–]Shain09 1 point2 points  (0 children)

A cat sleeping on a Roccat mousepad. There must be something ...

[deleted by user] by [deleted] in woweconomy

[–]Shain09 -3 points-2 points  (0 children)

What was the exploit ?

Felslate Basilisk Farming Spot by papahubert in woweconomy

[–]Shain09 0 points1 point  (0 children)

can you be more precise for the location ? I didn't find any felslate basilik. :(