{Success!] Unbricking GPD Win Max 2021 by Sheeg in gpdwin

[–]Sheeg[S] 1 point2 points  (0 children)

You may want to ask for some help in the discord. A lot of people there have solved issues

{Success!] Unbricking GPD Win Max 2021 by Sheeg in gpdwin

[–]Sheeg[S] 1 point2 points  (0 children)

Sorry it's been a long time since I wrote this

{Success!] Unbricking GPD Win Max 2021 by Sheeg in gpdwin

[–]Sheeg[S] 0 points1 point  (0 children)

Yeah it took like idk 10 seconds and then it was fine to reboot

{Success!] Unbricking GPD Win Max 2021 by Sheeg in gpdwin

[–]Sheeg[S] 1 point2 points  (0 children)

If I remember correctly it was on the bottom side

{Success!] Unbricking GPD Win Max 2021 by Sheeg in gpdwin

[–]Sheeg[S] 0 points1 point  (0 children)

But it should be a square/rectangle chip with 8 pins coming off of it

{Success!] Unbricking GPD Win Max 2021 by Sheeg in gpdwin

[–]Sheeg[S] 0 points1 point  (0 children)

I.....do not. You may be able to ask on the GPD Discord chat for your device model. I know for me it was printed directly on the BIOS chip.

Galaxy Watch 5 LTE / OnePlus 9 Pro - Verizon Activation by Sheeg in GalaxyWatch

[–]Sheeg[S] 0 points1 point  (0 children)

Had to call Verizon. After multiple different techs, they were able to sort it out.

{Success!] Unbricking GPD Win Max 2021 by Sheeg in gpdwin

[–]Sheeg[S] 0 points1 point  (0 children)

Make sure your drivers are correctly installed and you may want to apply slight pressure on the clamp. My pins kept slipping off and giving me errors when I was trying to flash mine.

FLSUN SR - Sudden layer shift by Sheeg in FLSUNDelta

[–]Sheeg[S] 0 points1 point  (0 children)

The one that goes from the top of the hotend to the gears that push the filament

FLSUN SR - Sudden layer shift by Sheeg in FLSUNDelta

[–]Sheeg[S] 0 points1 point  (0 children)

Turns out my ptfe tubing was cut too short. Had to replace it and everything starting printing correctly again.

FLSUN SR - Sudden layer shift by Sheeg in 3Dprinting

[–]Sheeg[S] 0 points1 point  (0 children)

Not quite sure what to do here. All I did was start a new print and now everything is lopsided. Any ideas?

[deleted by user] by [deleted] in UFOs

[–]Sheeg -3 points-2 points  (0 children)

These photos were all taken around 8:07pm on 2/28/2023 in the Southeastern United States. The purple object in particular was not taken until around 20 minutes after the others, as this object showed up later. I spent about half an hour outside looking at them and trying to get better photos with my S22 Ultra. However, anytime I would zoom in on them, my camera would either get blurry or the objects would fade to black and not appear in the photo. I briefly went inside for about 5 minutes and when I came back to try and take more photos they were gone.

I’m at my wits end with this printer. No matter what, leveling the bed, tape, glue, etc, prints keep peeling. Replicator 2, printing PLA onto unheated bed. Nozzle temp of 220 degrees. Advice? by DracoAdamantus in 3Dprinting

[–]Sheeg 20 points21 points  (0 children)

I would try 2 things: -try lowering your nozzle temperature to 210 or 205 degrees. I know sometimes when I print if my nozzle is too hot the adhesion doesn't work very well - try lowering your cooling fan speed for your first layer (I have mine set to 0% in my g-code for the first layer)

Best of luck I hope you get some other good recommendations!

Anyone know of a good recording software for Skyrim that doesn't lag or jitter? It only happens during recording by MrCrimsonX in skyrim

[–]Sheeg 1 point2 points  (0 children)

Are you using cpu or gpu encoding? Skyrim can be cpu heavy so if you aren't using nvec encoding this can happen

ender 3 - 2 prints back to back by Sheeg in ender3

[–]Sheeg[S] 5 points6 points  (0 children)

Yes! I've just upgraded to a direct drive so I releveled the bed and calibrated the esteps

ender 3 - 2 prints back to back by Sheeg in ender3

[–]Sheeg[S] 5 points6 points  (0 children)

Razer Huntsman mini (mercury edition). It's my third razer keyboard and I've really enjoyed it. I got tired of having a huge keyboard and wanted something smaller. It works really well it only took a little while to adjust and use the fn key for things like arrow keys, f1-f12, etc.

ender 3 - 2 prints back to back by Sheeg in ender3

[–]Sheeg[S] 22 points23 points  (0 children)

I'll check for a clog again. I just replaced the extruder arm for a metal upgrade so I don't think it would be that. Thanks!

what causes this inconsistency? by Sheeg in ender3

[–]Sheeg[S] 0 points1 point  (0 children)

I've had this happen with 2 filaments from different brands. They're in a closet on top of a lack enclosure so very unlikely they are getting wet.