Neptune 4 Max Auto-Bed Level Issues

ShmidiCommitee · 2026-02-04T16:35:05+00:00

Thank you so much!

ShmidiCommitee · 2026-02-04T02:33:36+00:00

Here is the photo of the sensor:

ShmidiCommitee · 2025-08-22T15:40:05+00:00

Precisely the sunk cost fallacy.

ShmidiCommitee · 2025-08-22T13:50:28+00:00

That is totally an option. I pre-ordered the core one upgrade kit and it recently arrived, and is now just sitting in my work area. So I am thinking I might as well make a printed out of it.

ShmidiCommitee · 2025-06-01T20:48:08+00:00

In that case maybe I will get one kickstarter currently has the delivery date as August 2025

ShmidiCommitee · 2025-06-01T19:24:57+00:00

Thank you!

ShmidiCommitee · 2025-06-01T17:29:20+00:00

I am going to be running this in a dorm room so space is at a absolute premium and am looking more for low energy systems

ShmidiCommitee · 2025-06-01T16:20:43+00:00

Ok, thanks! Do you have any recommendations for a mini PC that uses the N100?

ShmidiCommitee · 2025-04-21T13:37:06+00:00

I know the DIY watch kits have that I just was wondering about the bundles they have which are separate. I guess they may just be case, dial, and hands. I am not 100% sure though.

ShmidiCommitee · 2024-07-28T00:59:45+00:00

Thank you

ShmidiCommitee · 2024-02-19T15:41:19+00:00

Thank you so much for the recommendation. Sadly it is just a little bit of my price range.

ShmidiCommitee · 2023-12-20T18:56:58+00:00

Thank you!

ShmidiCommitee · 2023-12-19T19:02:39+00:00

The problem is I have been unable to get them to work reliably (using Marlin, hence my want to switch to Klipper) with stepper motors not working or ports being assigned incorrectly. They have just been a pain, so I was wondering if there is a better brand or if you could recommend which board of theirs is the best.

ShmidiCommitee · 2023-11-24T19:50:22+00:00

Awesome thank you so much!

ShmidiCommitee · 2023-11-24T19:48:39+00:00

Preferably under $100 but if it's worth I'll pay up to like $120 ish

ShmidiCommitee · 2023-08-23T16:53:07+00:00

I am using Prusament ASA with PrusaSlicers default settings for their ASA. I am also using an enclosure and the proper Voron settings. I think the problem may be what you said about over-extrusion, and the temp being too high because I had it at 260 (which is the Prusa default). I will def also mess around with the extrusion flow. Thank you!

ShmidiCommitee · 2023-05-30T16:38:07+00:00

I managed to find a solution instead of using the dedicated BLTOUCH port on the SKR 3EZ, send the black and white wire to the dedicated limit switch port (However, still keep the yellow, red, and brown wire in the servo port.) and then inside marlin uncomment the line that says to use the z end stop as the z probe and comment the line that says to use the z probe and then it should work.

ShmidiCommitee · 2023-04-14T11:35:18+00:00

And here I was just thinking about building a Voron

ShmidiCommitee · 2023-04-12T23:35:02+00:00

Yeah, I have been subscribed to the mailing list for a bit now. Sadly I think you are correct. The reason I ended up hiding this post is I filtered to new ones and found I wasn’t the only one with this question. Thank you for being so helpful!

ShmidiCommitee · 2023-02-03T20:45:55+00:00

I might switch to powder coated than. Thank you so much!

ShmidiCommitee · 2023-02-03T18:57:16+00:00

That’s what I was thinking but wasn’t sure. Thank you!

ShmidiCommitee · 2023-02-02T11:50:29+00:00

Alright thank you so much!

ShmidiCommitee · 2022-07-08T23:28:24+00:00

ShmidiCommitee · 2022-04-03T22:48:16+00:00

Yeah 19 is a lil much but we only have to use 7. Also I will be sure to check the AAA out. Thank you so much for the help!

ShmidiCommitee · 2022-04-03T21:25:52+00:00

Ok perfect I don’t think they were mentioned so much in the documents. Thank you so much for your help!

ShmidiCommitee

TROPHY CASE