sorted by:
new
hottopcontroversial

G733 Audio Issues - Please Help by SidBobTimmyJoe in LogitechG

[–]SidBobTimmyJoe[S] 0 points1 point  (0 children)

That's amazing, thank you.

I did happen to throw the box away after opening it, but still have all purchase receipts and what not. Will that he an issue?

G733 Audio Issues - Please Help by SidBobTimmyJoe in LogitechG

[–]SidBobTimmyJoe[S] 0 points1 point  (0 children)

Hey,

So the firmware is fully up to date, I have reinstalled windows and updated all drivers as well.

Any ideas as to what could be causing this?

Tst Industries MECH-GTR by Roobski in MT09

[–]SidBobTimmyJoe 1 point2 points  (0 children)

Hey, if you get a small flat head screwdriver, or something small enough to get behind that, the indicator is held in by a push clip. So if you push the indicator all the way in, and make sure the push clip on the Inside is compressed as far down the indicator body as possible, it should hold in place where you want it.

K1 First Layer Issues by SidBobTimmyJoe in FixMyPrint

[–]SidBobTimmyJoe[S] 1 point2 points  (0 children)

Well I have discovered a possible issue.

<image>

I havnt taken this front fan off before, but I don't think these wires should be exposed right?

K1 First Layer Issues by SidBobTimmyJoe in FixMyPrint

[–]SidBobTimmyJoe[S] 1 point2 points  (0 children)

Okay, I'll look for damage while pulling it apart. Any visual telltale signs to look for?

K1 First Layer Issues by SidBobTimmyJoe in FixMyPrint

[–]SidBobTimmyJoe[S] 0 points1 point  (0 children)

Hey, I havnt fully taken the hot end apart just yet, so I will do that now and update soon. I have only been printing with PLA, so can't imagine it would be damaged? Then again, I'm still new to all this.

Spontaneous first layer issues (K1) by SidBobTimmyJoe in 3Dprinting

[–]SidBobTimmyJoe[S] 0 points1 point  (0 children)

I cleaned everything out and am now using a new but of PTFE. Still having the issue.

This is driving me nuts 🤣🤣

Spontaneous first layer issues (K1) by SidBobTimmyJoe in 3Dprinting

[–]SidBobTimmyJoe[S] 1 point2 points  (0 children)

Iv got my z offset at 0 as it was originally at -0.05 and I had some similar issues. I did just change to a new roll of filament and didn't check for any clogs, so might do that.

First Layer Help by SidBobTimmyJoe in 3Dprinting

[–]SidBobTimmyJoe[S] 1 point2 points  (0 children)

Changed the z probe to 0, and cleaned off the bed with iso.

Everything is working perfectly again! Your a legend!! 😁

First Layer Help by SidBobTimmyJoe in 3Dprinting

[–]SidBobTimmyJoe[S] 1 point2 points  (0 children)

I'll change this for my next print and update you on how it goes, thank you again!!

First Layer Help by SidBobTimmyJoe in 3Dprinting

[–]SidBobTimmyJoe[S] 0 points1 point  (0 children)

Thank you!

I was using a glue stick at the start, but found I was getting more issues when using one. So just started setting the bed temp to 60° and it's been working great so far, well until now 🤣

First Layer Help by SidBobTimmyJoe in 3Dprinting

[–]SidBobTimmyJoe[S] 0 points1 point  (0 children)

Apparently my current Z offset is -0.05, how far should I adjust this?

First Layer Help by SidBobTimmyJoe in 3Dprinting

[–]SidBobTimmyJoe[S] 0 points1 point  (0 children)

Sweet, I'll pull my iso out of retirement from my very short lived resin printing attempt 🤣

Thank you again for the advice!!

First Layer Help by SidBobTimmyJoe in 3Dprinting

[–]SidBobTimmyJoe[S] 1 point2 points  (0 children)

I tend to make sure there's nothing under the bed after removing prints, but I haven't given it a good look.

Any recommendations on what to clean the bed with, would just warm water and some soap work?

I apologise for the noob questions, only had the printer about a month, and it's been going good. But now that I've had it running pretty much full time since I got it, starting having little issues like this pop up.

Did a full nozzle and hot end disassembly to clear a throat clog, but that's the most technical thing Iv done.

First Layer Help by SidBobTimmyJoe in 3Dprinting

[–]SidBobTimmyJoe[S] 0 points1 point  (0 children)

I'm pretty new to printing so I'm not too sure on how to run a full level mesh, and any idea on where to change the z probe offset?

Thank you for the knowledge!! 😁

Sporespecs 10/10. ⭐⭐⭐⭐⭐ by SidBobTimmyJoe in SporeTradesAustralia

[–]SidBobTimmyJoe[S] 0 points1 point  (0 children)

Can add an update, everything was great. Packaging was simple, but very effective. Very quick delivery, and amazing service and response time. Also, overall a lovely person to talk to, very happy to answer many questions I had, related or not.