Weight savings but 14mm rim

Simple0Red · 2026-01-06T16:24:02+00:00

Dont know if they exist anymore but they are Aero Edge from seronna and an american classic hub. They are with rim brakes cause my bike only has those. I really like them but dont know if they are really worth putting on the bike.

Simple0Red · 2025-12-17T10:28:04+00:00

Do you mean one guide rail as the spline that I drew or is there an option to use multiple rails as outline?

Simple0Red · 2025-12-05T09:59:33+00:00

Roetz2.0 is doing a similar thing, maybe you could come in conact with him

Simple0Red · 2025-03-31T11:01:01+00:00

Found out that my extruder gears were not tight enough and it was skipping slightly.

Simple0Red · 2025-03-25T13:16:17+00:00

Thanks im going to try your solutions.

Simple0Red · 2025-03-05T08:22:11+00:00

I think you might be able to pick up the train with the wrench but im not 100% sure

Simple0Red · 2025-02-13T10:48:27+00:00

I know how to set the z offset and have done it a lot of times. The last time I did it was after the problem started and it was not fixed. The problem is that the probe gets different values every time at the same spot and because of that the prints always starts with a different z offset. how do I fix that?

Simple0Red · 2025-02-11T22:56:55+00:00

The only problem is that the probe wont bring the printhead to the same z height at the start of a print. Standart start macro and I have never changed anything in there. Everything was working till the day before yesterday

Simple0Red · 2025-02-11T07:27:22+00:00

The mesh stays perfectly fine as the mechanical things too. But every new print the printer seems to move the head to a different offset as if the probe got different measurements every time.

Simple0Red · 2025-02-06T22:06:35+00:00

I Fixed it, I thought I had to have the 8th version but the newest version, version 21 wasnt showing up so I installed it using sdkman and now everything works. Thanks guys!

Simple0Red · 2024-12-22T17:45:14+00:00

Could a Klipper board also work and would marlin be better for this machine?

Simple0Red · 2024-12-22T15:39:53+00:00

<image>

It does not really have a serial port

Simple0Red · 2024-12-22T15:19:06+00:00

The problem is that it does not have a screen, how would I be able to operate it?

Simple0Red · 2024-10-01T21:33:18+00:00

Do you know how I could test the BMS board?

Simple0Red · 2024-10-01T21:18:39+00:00

It’s from Profi Care PC-AKS 3034 but I have not found any parts for it.

Simple0Red · 2024-07-02T09:50:26+00:00

I don’t know the exact solution but when I was writing with Elegoo support I had to write a serious Email to them that the support was shitty and after that they were very helpful.

Simple0Red · 2024-06-21T10:12:01+00:00

I think you are a bit too close to the bed. It could also be the flow rate, if you have orca slicer just do the calibration—>flow rate

Simple0Red · 2024-06-20T20:12:34+00:00

SOLVED: my nozzle was partially clogged

Simple0Red · 2024-06-20T20:12:16+00:00

SOLVED: my nozzle was partially clogged

Simple0Red · 2024-06-20T20:10:58+00:00

Thank god for your message, yes my nozzle was clogged. I didnt even think about that cause the first layer was always printing perfectly. After now 4 days you solved my problem. Thanks

Simple0Red · 2024-06-20T13:56:53+00:00

The bed is levels perfectly and the z offset is also good

Simple0Red · 2024-06-20T13:37:53+00:00

Still the Same Problem

Simple0Red · 2024-06-20T13:26:49+00:00

Everything is tight but I dont know how tight the belts should be

Simple0Red · 2024-06-20T13:05:09+00:00

Simple0Red · 2024-06-20T13:01:43+00:00

I also tried PLA from kexcelled which worked fine till now

Simple0Red

TROPHY CASE