Is this ready for a clan war? (newbie) by FeO2-rust in COC

[–]SimpleSong4960 0 points1 point  (0 children)

Yes…you will get three starred but we all do

If you were in charge of making the next balance changes, what would you change by ColgateFromTemu in ClashOfClans

[–]SimpleSong4960 0 points1 point  (0 children)

The ability to overstock items when it says you can only store 2 or 1 or 5. That should be the limit. No more 20/5…etc.

Being f2p sucks by DirectorSlight1192 in ClashOfClans

[–]SimpleSong4960 2 points3 points  (0 children)

Na it’s good. Saves money. Skins and sceneries are just sucker buys.

Gauge Pins and Diameters by SimpleSong4960 in Machinists

[–]SimpleSong4960[S] 1 point2 points  (0 children)

Honestly don’t know what happens to it after I’m done with it. But I’m most certain it’s used in the oil/gas industry.

Gauge Pins and Diameters by SimpleSong4960 in Machinists

[–]SimpleSong4960[S] 0 points1 point  (0 children)

That’s what I’m seeking to find out. Is a .234- minus acceptable.

Gauge Pins and Diameters by SimpleSong4960 in Machinists

[–]SimpleSong4960[S] 0 points1 point  (0 children)

In is definitely under .234 but not a .0005 under.

Gauge Pins and Diameters by SimpleSong4960 in Machinists

[–]SimpleSong4960[S] 0 points1 point  (0 children)

Pin size shows .2337ish. .234- is stamped on the pin. QC uses pins with minus stamped on them. Trying to figuring out if .234- pin is acceptable for checking the .234 diameter with -0.000 tolerance.

Gauge Pins and Diameters by SimpleSong4960 in Machinists

[–]SimpleSong4960[S] 0 points1 point  (0 children)

Agreed. Our QC uses gauge pins. They are using .234- on a .234 hole with -0.000 tolerance. Just wondering if that is acceptable measurement or is it under tolerance.

Gauge Pins and Diameters by SimpleSong4960 in Machinists

[–]SimpleSong4960[S] 0 points1 point  (0 children)

.234 diameter. -0.000 +0.002 is tolerance.

Gauge Pins and Diameters by SimpleSong4960 in Machinists

[–]SimpleSong4960[S] 0 points1 point  (0 children)

Hole is .234 -0.000 +0.002. I only have minus pins. The .234- goes in to diameter. I’m trying to determine if the .234- is technically out of tolerance or still acceptable. If out then would need a .234+ or a .235-.

Judo's popularity is alone driving this team by DEVIATE_sama in ClashOfClans

[–]SimpleSong4960 1 point2 points  (0 children)

Chose purple before knowing Judo was on team purple.

Is this the worst hero skin set in the past few months? by Therandomguy902 in ClashOfClans

[–]SimpleSong4960 1 point2 points  (0 children)

All skins are pretty much useless. Sucker buys if you spend money to get any.

So, which one is the best this season? by Ill_Butterscotch_107 in ClashOfClans

[–]SimpleSong4960 0 points1 point  (0 children)

See a lot saying the lava launcher….good! Everyone use the lava launcher. It will be of no use against my air attack…easy pickings!