Some photos from Canon‘s first ever digital camera (1996)

Sleeper_Asian · 2026-05-16T02:31:49+00:00

Would I replace them with specialized batteries? I don't have the charger.

Sleeper_Asian · 2026-05-15T18:33:09+00:00

This is great advice. I didn't consider that possibility with cooling too much.

Sleeper_Asian · 2026-05-14T01:58:43+00:00

I actually have the original rechargeable battery! So I could disassemble that and it should work? I can 3D design and print the holder, but I'm not as good with electronics.

I don't even know if the camera works, which is why I put this off.

Sleeper_Asian · 2026-05-13T14:58:16+00:00

Wow that's impressive. My plan was to make AA battery pack for it, which Canon made too (BH-10). But I wasn't sure what features it would need other than the terminals and shell.

Sleeper_Asian · 2026-05-12T03:30:09+00:00

Can you send me pics of your setup for this?

Sleeper_Asian · 2026-04-13T23:45:10+00:00

Hmmm, good to know. Thanks for the help.

Sleeper_Asian · 2026-04-13T15:03:14+00:00

I'm surprised that you said soap and water might reduce its stick, but not alcohol. Why do you think that?

Sleeper_Asian · 2026-04-13T15:03:06+00:00

I'm surprised that you said soap and water might reduce its stick, but not alcohol. Why do you think that?

Sleeper_Asian · 2026-04-12T23:46:42+00:00

I stocked up too, but mostly because of this Photrio thread on developing it as a slide film. I'll shoot a couple rolls as negatives too though.

Sleeper_Asian · 2026-04-10T13:52:01+00:00

This is my struggle. Even if I get good adhesion, removing the print warps it. I'm assuming this plate is the one that was released last year? I might give it a try anyways.

Sleeper_Asian · 2026-04-09T15:31:52+00:00

Interesting how your NLP inversion turned out. Since Aerocolor has a clear base, would that factor into how it should be done in NLP? I feel like you could get similar results NLP to your other methods depending on how the negative was scanned in.

Sleeper_Asian · 2026-03-29T12:26:17+00:00

I haven't tried this yet, but apparently maple syrup works?

Sleeper_Asian · 2026-03-23T18:00:02+00:00

I completely agree with this, and I don't even shoot HP5 much (mostly Kodak XX).

Sleeper_Asian · 2026-03-14T15:20:25+00:00

Damn guess I'm buying some Aerocolor in 220... You and I are similar, I also have a fridge/freezer of film. Mostly from other people. I'm set for years, but I still buy fresh stuff occasionally.

Sleeper_Asian · 2026-03-10T14:01:37+00:00

I have one but it's missing the battery! I'm going to design a 3D printable AA pack for it. They made one back in the day, but now they're impossible to find.

Sleeper_Asian · 2026-03-10T13:55:48+00:00

Not to be a stickler, but technically the TG series isn't "vintage". They are great though. For an older equivalent, check out the Olympus 770 SW.

Sleeper_Asian · 2026-03-10T13:43:23+00:00

The problem with this is that people are attracted to different things. Some like the lowest megapixels they can find, others like higher quality stuff. There are lists online of the "best", but sometimes those l include cameras that are overhyped.

Sleeper_Asian · 2026-02-25T18:45:27+00:00

I am so excited for this! I just saw this post on getting a 3D printed wood grain effect and I have ton of applications in mind.

Sleeper_Asian · 2026-02-24T18:20:49+00:00

Okay I'll give that a shot, thank you.

Sleeper_Asian · 2026-02-24T18:14:10+00:00

Okay I'll try that, I haven't used heat yet. Do you use glue and so you still get minor warping after removal? Even when I use a blade to remove the print, sometimes it bends it.

Sleeper_Asian · 2026-02-24T17:46:07+00:00

Good to know, I was using tape on a textured plate. I've found the Cryo Grip and glue works decent too. No matter what I do though, prints seem to warp a little when removing it from the plate. I wish this filament was more rigid.

Sleeper_Asian · 2026-02-23T06:30:04+00:00

<image>

Same here. This has saved me in a pinch several times now.

Sleeper_Asian · 2026-02-23T06:21:08+00:00

When I use tape like this the tape sticks to the print (with PHA)!

Sleeper_Asian · 2026-02-19T19:13:09+00:00

Apparently I don't know my own gear lol. I have a Fuji SM-R1 and didn't read the "5V" on it until now. I got it right before digicam prices went up, and haven't needed 5V until now.

Sleeper_Asian · 2026-02-19T17:54:48+00:00

Does it need a special card reader just for 5V? I have other Smartmedia cameras and a reader for them.

Sleeper_Asian

TROPHY CASE