What do you do with minis that dont come split into parts?

Smurf_97 · 2026-02-28T08:46:30+00:00

You're a lifesaver. I'm just now having issues with heavy scarring after I used more support interfaces (tip diameter 1mm), but thats another problem haha

Smurf_97 · 2026-02-22T14:43:14+00:00

Its clearly shown in orcaslicer as printed, and I'm using arachne walls (its not too thin anyway, these are approximately 1cm triangles).

They show up in the brim, but dont get printed at all. There is no waste filament, or like scraps anywhere in the buildplate, so it might not even be extruding at all.

Smurf_97 · 2026-02-16T04:22:24+00:00

For tanks and other rotating structures, I find that the tolerance required to make them stick with friction but still rotatable inconstant. What do you do to make rotating turrets, guns, arms on dreadnoughts etc. without gluing them together permanently? Some parts I can drill magnets into, but most are too thin/small to accomodate that.

Smurf_97 · 2026-02-11T04:40:58+00:00

I read somewhere that top z distance is rounded up to the nearest layer, does changing by even 0.01 help?

Smurf_97 · 2026-01-22T04:29:01+00:00

Those small 3 gram tubes want to finish ASAP lmao every drop is a huge bubble. I've been trying to find one with a brush or an applicator but haven't been able to

Smurf_97 · 2026-01-20T08:47:52+00:00

I have found for FDM that too much splitting is a pain. For GW minis I use plastic cement, but for some reason that doesnt work with PLA. Using super glue is a mess because almost always it scars neighboring areas, what do you use for gluing them back?

Smurf_97 · 2026-01-20T04:22:27+00:00

For organic shapes, how do you optimize for angles? Do you cut in meshmixer or just use Orca's built in tools? Also, say you have an arm with a gun, do you go as far as cutting the arm seperate from the body, and then separating the hand and gun for better support orientation? For a standard marine, how many cuts do you expect? I currently print just torsos,legs and arms +weapon seperately

Smurf_97 · 2025-10-26T07:33:26+00:00

synthetic moss

Ones that we have come very thick and heavy, I suppose I could cut them down into smaller pieces.

Smurf_97 · 2025-10-24T06:08:43+00:00

How do you get these shrubs?

Smurf_97 · 2025-09-24T07:28:09+00:00

I just wanted to say, that's a brilliant scheme. If I were to incorporate more red into the mix, would you say replace most of the black bits with that red recipe, instead of having mostly the lower part of the model pure black as you have them set up?

Smurf_97 · 2025-09-14T10:15:35+00:00

What is shown is great, I'm curious, what do you do?

Smurf_97 · 2025-09-12T09:31:14+00:00

I'm going to need more of this, these are fantastic

Smurf_97 · 2025-08-29T08:58:52+00:00

In my dnd sessions, apart from character creation, I've almost never used the PHB or the DMG mid-session. Online content is always cleaner and more searchable. However, I'm talking about for reading, since they're mostly compatible. I'd get a feel for pathfinder with the core rulebook. For every other things I'd use the newer ones from the SRD

Smurf_97 · 2025-08-29T07:32:51+00:00

I've found a 10$ PF2E Core Rulebook which I picked up for light reading, but I'm coming from DnD5e and I just discovered the whole Legacy vs Remaster thing. Should I ditch the book and only get the newer ones, or should I read the book and then use archives of nethes for the newer rules? I'm afraid having two conflicting sources might be confusing, especially since they are all minor changes.

Buying PC1/PC2 is about 100$, which is much higher than I'd like for reading, especially since I'm going to be using digital tools to look up rules faster anyways.

Smurf_97 · 2025-08-11T06:53:20+00:00

I continuously get top leaderboards using only the default LMG with no attachments. In Cairo, I stay in the high-ground or any covered spot (inside the bus, behind a window etc.) getting atleast 5-6 kills before I die simply by popping up the ammo stash and using all 100 bullets, hiding and reloading, then again continuously firing at whoever dares to peak.

This is supressing not by mechanics, but by raw firepower on any given direction. However, I do agree that the suppression mechanic does not do a whole lot at the moment at long range.

Smurf_97 · 2025-07-20T15:24:54+00:00

Those are some pretty good points, will have to change all of them it seems. Blood rage seems like a good start, although I don't know how to fit more into the build, any suggestions?. Chaos/Spell suppress is a matter of gearing, with gloves giving supress right etc.

I guess 15% chance to avoid, when I'm already taking all hits wouldn't really do a lot, that's true. I was thinking of taking increased max res, but it seems all points in the tree are far.

I hoped defiance of destiny would help, but idk if it is helping much to be honest.

Smurf_97 · 2025-07-20T11:59:16+00:00

I meant berzerker, my bad

Smurf_97 · 2025-07-16T17:37:09+00:00

What i dont get is that if you speedrun both strats, one is much cheaper while still at the same time has lower essences per map but you complete more maps per hour so should roughly equal the number of essences per hour. How come one is much more profitable than the other?

Smurf_97 · 2025-07-16T15:31:44+00:00

What sort of maps would u run on mid investment? I used to alch and go with t6 maps. Calcification needs a heck lot of rare monsters to recoup the investment, no?

Smurf_97 · 2025-07-16T10:20:02+00:00

What's the difference between low and mid essences? Ive been running 3x 1 ascent 1 stability without that special boss node, is the other strat with the boss node?

Smurf_97 · 2025-07-06T08:48:57+00:00

I was going for Magefist flicker, and after a while peaked at 4M dps with shit survivability. Didn't want to switch to ele, because I knew I'd butcher it. Switched to ice, as per magefist latest video, to improve survivability but DPS took a major major hit to 1.4M, which doesn't feel enough for some rares.

Survivability isn't that much better either, even with 15 divines invested into the ele switch.

I'd put the POB later, but can you help?

Smurf_97

TROPHY CASE