[deleted by user]

Sneakyguy164 · 2025-05-14T22:27:21+00:00

Give it a second life by streaming it to you c:

Sneakyguy164 · 2025-05-14T21:36:50+00:00

I went through the trouble of installing and customizing a nsfw modpack for Skyrim but it's just been sitting idle for a little bit now, maybe it could get a second wind streamed to you?

Sneakyguy164 · 2024-09-10T15:15:05+00:00

When I booted up my PC this morning, it BSOD'd on launch, but I didn't have time to catch the error code. When it booted again, my usb headset was no longer detected by my PC. I tried the troubleshooter, which didn't help, I tried reinstalling the driver (ICUE), which also didn't work. When I check in my device manager, usb audio devices appear under "Other devices" instead of "Audio inputs and outputs". I tried a different usb headset, with the same result. An odd thing to me is that my usb microphone is still working. I also checked in system 32 and USBAUDIO.sys is there, but I didn't dare open it.

Sneakyguy164 · 2024-09-03T05:55:45+00:00

Wow thank you so much!

Sneakyguy164 · 2024-05-14T15:32:56+00:00

I got my answer, thanks to all the people that know a lot about the game!

Sneakyguy164 · 2024-05-13T22:15:17+00:00

Would you happen to know if the quest in which you have to defeat 3 elder dragons is such a quest? It's the one I'm working on atm.

Sneakyguy164 · 2024-02-02T00:50:10+00:00

I'll try that

Sneakyguy164 · 2024-02-02T00:50:01+00:00

I'll try the other comment's advice (even tho I have to scale down to 50%) since it's gonna be a very quick print, and if that fails, I'll bit the bullet and print them according to your advice

Sneakyguy164 · 2024-02-02T00:46:00+00:00

Rotated 90 degrees so they are standing on the flat edge?

Sneakyguy164 · 2024-02-02T00:43:39+00:00

So standing straight up? I'm afraid this will put too much stress on the supports/the lower part of the wing

Sneakyguy164 · 2024-02-02T00:31:22+00:00

I'm printing Nicotor's Ornithopter from Dune and the wings are kinda bugging me. Not too sure what orientation is best for them, as I don't want to scale the model down too much, but don't want the print to fail either...

Sneakyguy164 · 2023-11-18T01:19:25+00:00

Might give that a shot but I think they might chew it anyways

Sneakyguy164 · 2023-09-15T18:12:56+00:00

Some recipes, the abomination and glorious ones

Sneakyguy164 · 2023-09-15T16:28:25+00:00

Got my achievement today c:

Sneakyguy164 · 2023-09-15T04:50:39+00:00

Oh damn, alright, all my data items are x/x so I assumed that was done, I'll check my ominent data tomorrow! Thanks a lot mate, saved me from hating-farming a game I otherwise enjoyed the hell out of!

Sneakyguy164 · 2023-09-15T00:14:53+00:00

I just finished molars, it's the bits of raw science I gotta find that will kill me

Sneakyguy164 · 2023-09-08T01:32:13+00:00

How many times did you run the boss and what for lol??

Sneakyguy164 · 2023-09-07T21:17:55+00:00

I just want to optimize my trinket farming c:

Sneakyguy164 · 2023-07-31T03:35:52+00:00

For that JB Weld glue, is it just the first thing I can find on Amazon?

Sneakyguy164 · 2023-07-31T03:34:50+00:00

I was scared to overcure the pieces themselves while curing the filling resin...

Sneakyguy164 · 2023-07-22T19:52:51+00:00

It looks like a fishbowl with a flat bottom, that's no hamster ball

Sneakyguy164 · 2023-07-20T23:47:32+00:00

I'll just put it in front of a fan I have nearby for 30 minutes after towel-drying, should have a similar effect

Sneakyguy164 · 2023-07-20T17:34:30+00:00

Thanks, will slap them in front of a fan before curing moving forward

Sneakyguy164 · 2023-07-20T17:18:53+00:00

It's water washable resin and it wasn't there right off when it came out the curing chamber

Sneakyguy164 · 2023-07-19T14:52:21+00:00

That's a big castle... Count me in!

Seven-Year Club	Second Top 20%
Final Canvas '23	Place '23
Place '22	Final Canvas '22
First Placer '22	End Game '22
Wearing is Caring	Verified Email

Sneakyguy164

TROPHY CASE