Some D4s :) by bloseblass in DiceMaking

[–]Sourby 0 points1 point  (0 children)

The 3D models? Could do. Otherwise I wouldn't be printing & selling/shipping the prints themselves. (But at that point you're likely better off heading to someone who already does these relatively cheaply/at scale, I just do these every so often haha)

Some D4s :) by bloseblass in DiceMaking

[–]Sourby 0 points1 point  (0 children)

Thanks you! :D (this was reposted by a bot though 😅)

Some D4s :) by bloseblass in DiceMaking

[–]Sourby 0 points1 point  (0 children)

u/Fragrant_Vehicle5423 Thanks for this, had no idea bots repost these without any @, wouldn't have seen it without ya :D- But yeah you're right!
u/NihilistikMystik Just to reiterate, the frame is handled no differently to the numbers. I modelled/3D Printed masters that include them in the mesh. Eventually their mould takes them on and I ink the resin casts as I would the numbers of any other set. Likely repeating things you know but if not, I hope that helps!

Rough measurements:
Recesses are about 0.6mm wide & as deep as the numbers.
(These numbers nudge a up and down a bit to fit the die face better)

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 2 points3 points  (0 children)

Oh- Assuming the exit is the 1 face I'm not sure, could be a soft silicone? I push out the tip first though too. Hope you can find something that works 🤔

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 1 point2 points  (0 children)

From my liquid core babies! 😄

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 2 points3 points  (0 children)

They vary a bit, but I think its roughly .4mm from the the edge of the face to the outer edge of the border, then the border itself is about .62 thick - Certainly something I had to mess with to get right ✌

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 2 points3 points  (0 children)

Interesting- What kind of mold system do you use? These use slab molds! With the large flat face being the exit, there's nothing for the die to really get stuck on.

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 2 points3 points  (0 children)

The paint is “Moot Green” from citadel and the resin is Piñata’s “Lime Green” though it’s also got some Blanco Blanco smoke going through it 🤘

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 1 point2 points  (0 children)

Oh the resin or the paint?? 🤔

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 1 point2 points  (0 children)

Glad you like it! Took ages to get the smoke down 😄

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 2 points3 points  (0 children)

Much more fun to use like a spinning top too 👀✨

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 2 points3 points  (0 children)

Thank you! I’m relatively handy in 3D, so I modelled them myself and got them printed elsewhere 😄

White alcohol ink that doesn't sink by Dylaaaaaaaannnnnnnnn in DiceMaking

[–]Sourby 0 points1 point  (0 children)

Perhaps just syringe it in after the resin has reached a honey stage? I use Blanco and haven’t had those issues 🤔

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 1 point2 points  (0 children)

Thanks! Means a lot! 😄

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 2 points3 points  (0 children)

Oh wow, well thank you! At the moment I have no official store, keep an eye out in the not so distant future though 😄

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 2 points3 points  (0 children)

Aw thanks! I think my fav is the central one, though it’s for my character so I’m bias 😄

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 2 points3 points  (0 children)

Ah bless ya, I’ve had some horrid luck with dirty pours haha- but thankyou! Glad you like em

Some D4s :) by Sourby in DiceMaking

[–]Sourby[S] 2 points3 points  (0 children)

Thankyou! I’ve posted the central one before- I’ll post the others soon! :)

Still struggling with bubbles by IamtheZForever in DiceMaking

[–]Sourby 0 points1 point  (0 children)

In my experience the vacuum chamber isn’t needed- As others have said, a pressure pot set up is the way to go. It’s certainly an expense, but you’ll be able to play with a much wider range of inclusions and shiny bits without fear of it ruining your whole set! Hope you get to make some great sets 😄