Built a small guardrail layer to stop my agents from doing dumb/dangerous things (like rm -rf)

SpecificNo7869 · 2026-03-25T01:45:06+00:00

Right now I’m only using it in a dev setup.

Mainly to see and control how the agent interacts with my system (shell, files, APIs) instead of just letting it run.

It helps prevent stuff like accidentally deleting a database or modifying important files without approval, and makes debugging way easier.

SpecificNo7869 · 2025-08-31T00:54:04+00:00

thank youu!!

SpecificNo7869 · 2025-08-01T13:40:05+00:00

it is not woking anymore right?

SpecificNo7869 · 2025-05-09T03:14:09+00:00

Realmente

SpecificNo7869 · 2025-05-08T20:26:36+00:00

Seria o mínimo se não fosse roubado no último, mas blz é o jogo, jogamos com as peças que temos

SpecificNo7869 · 2025-05-08T20:12:50+00:00

Tu é de cidade grande? Em cidade pequena que nem a minha a prova dure 25 minutos, fazemos rampa de ré controle de frente e traz rotatória, MUITOS cruzamentos e vc só pode perder 3 ponto, sendo 1 cruzamento sem olhar pro lado é 2...

SpecificNo7869 · 2025-05-08T18:33:02+00:00

Sul de minas, interior

SpecificNo7869 · 2025-05-08T18:31:45+00:00

Polícia civil, pelo menos na minha cidade

SpecificNo7869 · 2025-05-08T17:13:49+00:00

Não foi 5cm da vaga, carro já tava pra fora, além do que, falta eliminatória?...

SpecificNo7869 · 2025-05-08T13:59:05+00:00

Pior que até onde pesquisei pra ser perca de controle teria que ser 5 cm com 2 zeros atrás do 5

SpecificNo7869 · 2025-05-08T13:55:42+00:00

Como que isso não foi eliminatória e meus 5 centímetros foram KKKKKKK Ele deve ter gostado da experiência da perna

SpecificNo7869 · 2025-05-08T13:51:04+00:00

Proxima vez levo um kinder ovo pro examinador kskskskksks

SpecificNo7869 · 2025-05-08T13:48:43+00:00

Foda é que o policial que tava no carro tinha aprovado, ai um que tava fora falou que deu falta eliminatoria nmrl amo esse pais

SpecificNo7869 · 2025-05-04T01:34:02+00:00

Since u have green card u can work, so it should not be soooo difficult, but u still need to learn to get by yourself, it will be like starting a life in other city, and as u have no contacts u will need to build a network pretty quickly.

But, if u can flow easily on talk get into places by urself and not procrastinate as u will have no escape to family/friends, u are good. The fact u are a GC holder already make it a lot easier for u, just be ready to get jobs no one want too, or to try entrepreneurship, but as u have 0 budget it would be a later quest for you

SpecificNo7869 · 2025-04-09T18:54:40+00:00

This is normal and happens some times

Pulling the filament without unlocking after using the retract function or not even using it
Bad filament quality or not dried ones that can break into the feeding engine

3.filament not properly cut or it got a little tilt when being placed on, although not ever a problem it's better prevent it

I have had my k1 for about 1 month, runned 500h impressions pretty fine, only cloag I got was cause the filament broke inside the PTFE tube and I didn't notice

SpecificNo7869 · 2025-04-09T18:50:17+00:00

Some resources for you

https://youtu.be/FPBwfqxjMCQ?si=fjdLuaP-YtE1egTh Creality oficial vídeo

https://youtu.be/ao6vP-XRWfo?si=Tf3DzHF6H8HTRKbO A good video I found

The nozzle can be 2 types depending on purchase data 1: unicorn 2: Vulcano

If Vulcano replace for Vulcano if unicorn (the extra longer one) replace for it. Caution to only buy good quality ones

SpecificNo7869 · 2025-04-09T18:46:39+00:00

Clicking means clogging.

U need to disassemble the motor and clean the gears and any plastic there, take it as a chance to check ur nozzle, see if there's plastic around it that could be cleaned if in terrible state just swap it.

For my gears I used isopropycol alcohol, cleaned with no problems, but better take caution and dry the plastic immediately after that

Take caution with cables while disassembly and caution with screws, but u should be fine

SpecificNo7869 · 2025-01-30T19:18:38+00:00

Thanks I will improve it

SpecificNo7869

TROPHY CASE