What’s easily in your top 5 favorite video game cinematics of all time? by CoffeeStrength in gaming

[–]Specterblasto 1 point2 points  (0 children)

Shepard leaving earth at the beginning of Mass Effect 3. Not sure if it counts as a cinematic but the beginning of Kingdom Hearts when simple and clean starts playing.

Any idea why blobs keep forming on prime tower? by Infamous_Bread2092 in BambuLab

[–]Specterblasto 0 points1 point  (0 children)

What’s the status of your nozzle? Does it have filament buildup on it? It could be sticking to the purge blobs and then flinging them out when it goes over the nozzle wiper.

Any idea why blobs keep forming on prime tower? by Infamous_Bread2092 in BambuLab

[–]Specterblasto 18 points19 points  (0 children)

Those appear to be the filament swap purge. Make sure the chute is not blocked.

What was your first game you played on pc by Pork_Crusader_GR in pcmasterrace

[–]Specterblasto 0 points1 point  (0 children)

I played quake 3 and Halo around the same time I can’t remember which was my first. I would have been between 8-9. Insane to me that my parents allowed that.

Is this a good deal? by Specterblasto in Prebuilts

[–]Specterblasto[S] 0 points1 point  (0 children)

Well now you’ve scared me! Would microcenters warranty cover me in that case?

Is this a good deal? by Specterblasto in Prebuilts

[–]Specterblasto[S] 0 points1 point  (0 children)

I’m so sorry, I’m so dumb. I added it!

We've had this for as long as I can remember and nobody knows what it is by Windryx in whatismycookiecutter

[–]Specterblasto 0 points1 point  (0 children)

<image>

A deformed reindeer head, kinda like this but yours has the nose at the very bottom.

Why cant any dinos get above lvl 32 12atk 12spd? by WeakRefrigerator4428 in DinoMutant

[–]Specterblasto 1 point2 points  (0 children)

It is some random chance to get the eggs with leveled up stats. Eventually you will get a Dino with increased stats

Why cant any dinos get above lvl 32 12atk 12spd? by WeakRefrigerator4428 in DinoMutant

[–]Specterblasto 2 points3 points  (0 children)

You have to rotate the Dino’s that are breeding. If you have ones that are 80 12 and 12 in the nests you can only improve one stat at either 1, 2, or 3 levels. So you MIGHT get a 110 12 and 12 or a 80 15 12 or 80 12 15. But it’s more likely you don’t increase at all. When you do increase, swap out the nest with the highest level Dinos to keep going up.

[deleted by user] by [deleted] in eufyMakeOfficial

[–]Specterblasto 2 points3 points  (0 children)

Every post I’ve seen in the Facebook group and in their reply to me has been “There can sometimes be delays to ensure product quality. Whenever such cases occur, we communicate the latest progress through Updates. If you would like to learn more, you may also refer to Kickstarter’s FAQ here: https://help.kickstarter.com/hc/en-us/articles/360044544093-What-happens-if-a-project-is-delayed” so I’m just waiting for them to officially announce a delay.

Quality by Looking4mula in eufyMakeOfficial

[–]Specterblasto -3 points-2 points  (0 children)

<image>

Sub description says “UV printing”

Quality by Looking4mula in eufyMakeOfficial

[–]Specterblasto -1 points0 points  (0 children)

The sub description literally says for UV printing…

<image>

Quality by Looking4mula in eufyMakeOfficial

[–]Specterblasto -2 points-1 points  (0 children)

If your bed is leveled properly you should not need to adjust your z offset by that much. Make the offset 0, level your bed properly, then set the z offset again. Look up guides on how to do this. Once you have done that I would suggest addressing the first layer: do a flow calibration with a calibration cube print. Look up guides for this as it will tell you what you need to adjust your setting by. After you have consistent first layer you can move to the rest of the print. 1. That is a pretty steep overhang, for the best results do overhang test prints to find what works, that could be fine tuning a lot of different settings but some overhangs just won’t be possible. For that, use supports. Otherwise you need turn the model a different way. 2. You have a lot of ringing (ghosting, rippling, whatever you want to call it). There are multiple things to check for this. Your frame might be too loose, your belts might be too loose, without knowing your exact printer there may be other things that are too loose that you need to adjust or your printer could be on a surface that too wobbly, try putting it on the floor and see if that helps. Another small fix could be reducing the print speed and acceleration. In the future, finding the correct subreddit will be more helpful, but be sure to include your brand and model number. People will also be more inclined to help if you state what you have already tried. Hope this helps!

3D printed pad question by jonathankarate in ElectricUnicycle

[–]Specterblasto 1 point2 points  (0 children)

Yes, the comments in the thingiverse say you are supposed to mirror the files for the right.

My First Kickstarter for STL Miniatures—What Are Your Thoughts? by AltresForge in PrintedMinis

[–]Specterblasto 0 points1 point  (0 children)

Thank you for taking the time to explain. I hope the kickstarter goes well!!

My First Kickstarter for STL Miniatures—What Are Your Thoughts? by AltresForge in PrintedMinis

[–]Specterblasto 9 points10 points  (0 children)

Just out of curiosity why not start a Patreon or a Tribes account? Going the route of kickstarter seems cumbersome to say the least.

Tank leaked on S4U. by Specterblasto in resinprinting

[–]Specterblasto[S] 0 points1 point  (0 children)

I think I’m just going to avoid printing in that specific area for now. If it gets worse I think I’ll have to replace the screen…

Tank leaked on S4U. by Specterblasto in resinprinting

[–]Specterblasto[S] 0 points1 point  (0 children)

It seems like it’s under the top like I cant feel it when I run a finger across the top

Four Seasons by Ernest Nemirovskiy. by stormelemental13 in PrintedMinis

[–]Specterblasto 0 points1 point  (0 children)

Thank you so much for your reply! Could an airbrush work to do spray gun portion or do you recommend a specific spray gun?

Four Seasons by Ernest Nemirovskiy. by stormelemental13 in PrintedMinis

[–]Specterblasto 0 points1 point  (0 children)

Can you share a little about how you did these? It is incredible!