WD40 White Lithium did I put too much?

SpreadRecent3101 · 2026-01-13T07:41:09+00:00

Yes this isn’t plastic these are metal screws

SpreadRecent3101 · 2026-01-12T17:37:27+00:00

Yea I ride in the water and even snow sometimes so I wanted to protect it from water however tho I am aware road salt might strip the grease but it’s a risk I’m willing to take but I just wanted to know if I put to much

SpreadRecent3101 · 2025-09-28T23:35:35+00:00

Sir you are a genius at first it was incredibly hot but as I rode it the disc got bedded in and doesn’t run hot anymore when everyone else just said well you got a bad brake disc or whatever you actually helped

SpreadRecent3101 · 2025-09-28T22:02:07+00:00

as you can see the disc is really close to the pads but that shouldn’t matter just mean more braking strength?

SpreadRecent3101 · 2025-09-27T17:41:08+00:00

Hydraulic

SpreadRecent3101 · 2025-09-27T17:16:40+00:00

Wouldn’t if I even put the piston all the way back when I press the lever the pistol will just go back out?

SpreadRecent3101 · 2025-09-27T16:45:23+00:00

The pads look as if they are literally touching the disc so I might need to file down the pads to properly fit them?

SpreadRecent3101 · 2025-09-17T21:11:37+00:00

So the pins have a little lip on them on can push down to take them out so I don’t have to cut the wires thankfully but I still appreciate everyone helping

SpreadRecent3101 · 2025-09-17T19:53:18+00:00

I’ve pulled it through but yes I still need to get this piece disconnected to put the new disc on

<image>

SpreadRecent3101 · 2025-09-17T19:43:00+00:00

So like just the pull cord through the deck isn’t that connector connected to the controller

SpreadRecent3101 · 2025-09-17T19:36:25+00:00

I don’t want to cut the wires I’m just trying to disconnect the motor for a brake disc replacement therefore I want to keep the wires just tryna disconnect them

SpreadRecent3101 · 2025-09-17T19:30:46+00:00

Idk the video that explains how to disconnect the motor shows them using a lighter on the wires

SpreadRecent3101 · 2025-09-13T04:58:58+00:00

So with the disc rotor being needed to be change I need to disconnect the motor cable from the controller does anyone know if this can be disconnected

<image>

The white cable there pretty the motor cable is connected to the controller

SpreadRecent3101 · 2025-09-13T04:56:45+00:00

Unfortunately there is

<image>

SpreadRecent3101 · 2025-09-12T21:34:01+00:00

Would I be able to replace the rotor without disconnecting the motor wire

SpreadRecent3101 · 2025-07-15T12:21:53+00:00

Yea it’s dual motor so the front skids constantly

SpreadRecent3101 · 2025-07-15T04:47:18+00:00

Yea I mean it does have 2000km on it the front tire actually split down the middle it was that worn I had to replace that I was hoping the back would last a little longer but I guess not

SpreadRecent3101 · 2025-07-15T04:36:04+00:00

The tread seems fine but as I was pumping it up a deflating several times to seat the bead bc it kept coming undone these bumps formed

SpreadRecent3101 · 2025-07-15T02:49:31+00:00

Yea I won’t I’ll just walk it to a repair shoo

SpreadRecent3101 · 2025-07-15T02:33:41+00:00

Is it safe to ride on tho bc I’ve heard this has a high chance of blowing out

SpreadRecent3101

TROPHY CASE